Termékek önálló vállalati környezet (34)

Il panettone è un tradizionale dolce natalizio italiano, originario di Milano. Caratterizzato dalla sua forma alta e a cupola, è realizzato con un impasto lievitato dolce, arricchito con frutta candita, uvetta e scorza d’arancia. La sua preparazione richiede diversi giorni per la lavorazione e la lievitazione naturale, che conferisce al dolce la sua consistenza soffice e il sapore distintivo. Il panettone è spesso associato al periodo natalizio ed è apprezzato sia in Italia che a livello internazionale come simbolo della tradizione e dell’artigianalità italiana. confezioni da 12, 1 pallet = 10 confezioni, scadenza 30/04/25 Minimo ordine : 30 pallets

Sanazieg Adhesive high breathability and moldability mortar, based on hydraulic lime, for filling the vanishing points between elements in stone, brick, mouldings, decorative articles etc., in ecological building interventions, new buildings and in the restoration of vintage buildings and monuments. It can be added with earth colours, ornamental aggregates etc. Sanazieg is a product consisting of hydraulic lime, botticino, kaolin, calcium caseinate, Vichy salt, tartaric acid, ammonium salts and natural fibres. It has high hygroscopicity and breathability, contains no cements, resins, solvents and radioemissive substances. Jointing and filling interstices between bricks, or between bricks and stones, in mouldings, and in decorative articles, etc., in interventions of restoration and rehabilitation of old buildings and buildings of historical interest. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". Pour about 2/3 of the mixing water into the mixer. Gradually add Sanazieg and the water still required, continue to mix until a homogeneous, lump-free mixture of the desired consistency is obtained. The mixing water indicatively necessary is equal to 14%-16% by weight (3.5 - 4 litres per 25 kg bag). Apply with trowel, mechanical plastering machine, etc., in the interstices prepared as specified. To highlight the aggregate, use a sponge or a wet brush as soon as the plaster Sanazieg begins to harden. For more significant removals, spray retardant solutions like PRERIT, immediately after spreading. Approximately 1.6 kg of Sanazieg for each cubic decimetre of volume to be filled (on average 10-15 kg/m² of solid brick masonry to fill). Bag 25 kg - Pallet: 50 x (Bag 25 kg)

The Microencapsulated Vanilla Fragrance delivers a warm and comforting scent that captures the essence of pure vanilla. This fragrance is perfect for creating a cozy and inviting atmosphere, making it ideal for use in air fresheners, scented candles, and personal care products. The microencapsulation technology ensures that the vanilla scent is released slowly, providing a long-lasting and consistent aroma that soothes the senses. With its rich and creamy notes, the Microencapsulated Vanilla Fragrance is a favorite for those seeking to infuse their environment with a touch of warmth. The fragrance is crafted with high-quality ingredients, ensuring a pure and authentic scent that stands out. Whether you're looking to enhance your product offerings or simply enjoy the comforting aroma of vanilla, this fragrance is a versatile and effective choice. Its enduring scent ensures that your space remains cozy and inviting for extended periods.

Sanastark Reactive solution of mineral silicates, capable of forming binding and stabilizing compounds for hardening and consolidating treatments by reaction with hydrated calcium salts and moisture present in masonry, plaster, stone and concrete. Indicated in the preliminary treatments to the subsequent plastering or smoothing operations, of plasters and powdery mortars and wall casings in general, in green building interventions and in the restoration of period and monumental buildings. Sanastark is a solution based on mineral silicates, demineralised water and natural dispersant. It does not contains traces of resins, solvents or thinners. The application of Sanastark does not affect the original wall breathability. Cortical reinforcement and elimination of pulverisation of mortars, plasters and masonry jointing. Also suitable as a natural fixative before applying lime putty- or potassium silicate-based plasters and paints. Remove the soilings and saline manifestations by vigorous brushing. Then eliminate the residual dust. Saturated with water until you reach the condition of "saturated with dry surface". Apply by spraying, proceeding from the bottom up: it can also be applied with a brush with natural long bristles. In the presence of pronounced degradations proceed with several applications, wet on wet. From 0.20 to 0.30 kg of Sanastark for each square metre of surface to be treated, based on the porosity of the support. Plastic can 5 kg - Plastic can 10 kg - Plastic can 25 kg

Floor Level Floor Level is a self-levelling modified-polymer cement mortar with fibre-reinforcement, offering accelerated grip and fast hardening. Applied prior to laying the flooring, it is perfect for levelling at thickness ranging from 3 mm to 20 mm so as to adapt to any type of covering. Floor Level is a self-levelling modified-polymer cement mortar with fibre-reinforcement, offering accelerated grip and fast hardening. Applied prior to laying the flooring, it is perfect for levelling at thickness ranging from 3 mm to 20 mm so as to adapt to any type of covering. Floor Level is a self-levelling modified-polymer cement mortar with fibre-reinforcement, offering accelerated grip and fast hardening. Applied prior to laying the flooring, it is perfect for levelling at thickness ranging from 3 mm to 20 mm so as to adapt to any type of covering. Packaging: 25 kg bag UM: €/kg

Pomodorini Datterini gialli al naturale - Pomodori non pelati interi - La Torrente Questa speciale varietà di pomodorini viene coltivata in collina, ad un'altitudine di oltre 500 metri, nella Val Fortore e precisamente nel comune Beneventano di San Bartolomeo in Galdo. Il microclima e la conformazione del terreno ne permettono la coltivazione senza irrigazione. I pomodorini Datterini sono una pomodorini dalla caratteristica forma allungata, dall’elevato grado zuccherino, con pochi semi e una buccia sottile. Povero di calorie, è ricco di sali minerali e vitamine nonchè di antiossidanti. Pomodori 100% Italiani CONFEZIONE DA 6 1 PZ =E URO 2,90 SCADENZA 31 / 12/ 2026 MINIMO D'ORDINE 30 PALLET

Foglie di carciofo,100% Italiano. Versatili in cucina, si adattano a molte ricette. Possono essere usate sott’olio oppure utilizzate per condire le lasagne o la pasta ma anche per arricchire zuppe e brodi. Particolarmente pratiche, le foglie di carciofo Citres hanno un basso contenuto di aceto quindi si adattano perfettamente su Focacce, Pizze e altri prodotti da forno salati senza lasciare un sapore acido sul cibo. I nostri carciofi sono 100% italiani e lavorati da prodotto fresco ad aprile e maggio. Questo tipo di lavorazione mantiene un alto nutriente organolettico, lasciando le verdure croccanti e saporite senza “stressare” il prodotto che viene subito dopo invasato in modo semplice e naturale. AL NATURALE con acqua e sale 2300 g CONFEZIONE DA 4 1 PZ =EURO 4.90 1 PALLET 20 CONFEZIONI DA 4 SCADENZA 20 / 05/2027 MINIMO D'ORDINE 30 PALLET

Il panettone è un tradizionale dolce natalizio italiano, originario di Milano. Caratterizzato dalla sua forma alta e a cupola, è realizzato con un impasto lievitato dolce, arricchito con frutta candita, uvetta e scorza d’arancia. La sua preparazione richiede diversi giorni per la lavorazione e la lievitazione naturale, che conferisce al dolce la sua consistenza soffice e il sapore distintivo. Il panettone è spesso associato al periodo natalizio ed è apprezzato sia in Italia che a livello internazionale come simbolo della tradizione e dell’artigianalità italiana. confezioni da 16, 1 pallet = 12 confezioni, scadenza 30/04/25 Minimo ordine : 30 pallets

Il panettone è un tradizionale dolce natalizio italiano, originario di Milano. Caratterizzato dalla sua forma alta e a cupola, è realizzato con un impasto lievitato dolce, arricchito con frutta candita, uvetta e scorza d’arancia. La sua preparazione richiede diversi giorni per la lavorazione e la lievitazione naturale, che conferisce al dolce la sua consistenza soffice e il sapore distintivo. Il panettone è spesso associato al periodo natalizio ed è apprezzato sia in Italia che a livello internazionale come simbolo della tradizione e dell’artigianalità italiana. confezioni da 12, 1 pallet = 10 confezioni, scadenza 30/04/25 Ordine minimo : 30 pallets

Sanaxil I Natural, protective, decorative, breathable, pigmented, non-toxic, anti-mold plaster, with stabilized potassium silicates, for interiors and exteriors. Substantially mineral formulation which, thanks to the natural alkaline pH of potassium silicate, develops a strong antibacterial and anti-mold action. Sanaxil I is a versatile and valid product in various application fields: in green building interventions, in new constructions and in the restoration of period and monumental buildings. The product does not form a film, thus avoiding detachment and flaking phenomena and, while ensuring excellent water repellency, ensures high values of permeability to water vapor thanks to its porous and microcrystalline structure, perfectly compatible with mortars, plasters and all other common elements of the body masonry. Physical-mechanical performance and durability are coupled with a vast choice of colors that cannot be altered over time; characteristics which, combined with the ease and practicality of application, make the product extremely versatile and adaptable to any project requirement. Restoring protective coatings based on stabilised potassium silicates, for vertical and horizontal surfaces. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". Existing paints (washable, organic, solvent-based etc.) must be removed. Homogenise the surfaces by applying the fixative Sanaxil Fix. Spread SANAXIL in two coats: the first, for simple deposition, with steel trowel, the second, for spreading and finishing, with sponge float. The application of the second coat must be carried out, when the first coat starts to dry, under one of two suggested conditions: with dry trowel, for smooth surfaces; with moistened trowel, for antique-effect surfaces. Sanaxil I is dry to the touch after 4 hours, it can be overcoated after 2-5 hours, while it will be dry in-depth after 16-32 hours. Indicative consumption depending on the different particle sizes of Sanaxil I available: 1 mm GRAIN: approximately 1.25 -1.40 kg/m²; 1.2 mm GRAIN: approximately 1.40 -1.55 kg/m²; 2 mm GRAIN: approximately 1.85 -2.15 kg/m²; 2.2 mm GRAIN: approximately 2.00 -2.30 kg/m². The indicated yields refer to smooth supports and are for guidance only. Actual consumption must be identified with a suitable practical test. Pail 5 kg - Pail 25 kg

Sanalink Hydraulic lime and natural light aggregate based fibre-reinforced mortar. It has high water vapor permeability characteristics, low bulk density (reduced thermal conductivity) and limited water permeability. Ideal for the construction of internal and external walls and masonry for new buildings, the renovation of existing buildings, green construction and the restoration of antique and monumental buildings. Sanalink has exceptionally strong water vapour permeability and adhesive properties and a particularly low elastic modulus. Its reduced bulk density makes it particularly advantageous in determining the thermal values ​​of the masonry, thanks to the thermal conductivity values, inferior to conventional cement mortars or lime based. It has physical, chemical and aesthetic properties very similar to antique mortars and is composed of raw materials of natural origin. The combined use of natural binders, micro-fibres and light inert pozzolanic materials guarantees high quality performance in terms of ductility, chemical resistance and water vapour permeability. It can be used for brickwork, tuff, stone and mixed masonry walls and is therefore recommended for the restoration of antique masonry, green construction and, in general, quality interior and exterior constructions. Mortar used for the construction and rehabilitation of interior and exterior masonry in solid or perforated concrete blocks, perforated bricks, solid bricks, tuff, natural stone and stone blocks in general. Application surfaces must be clean, free of dust, contamination, crumbling, inconsistencies, etc., and adequately saturated-surface-dry with water. Add approximately out 2/3 of the mixing water to the mixer and gradually add Sanalink and the rest of the water until a homogeneous, lump-free mixture of the desired consistency is obtained. The required mixing water is approximately 12-16% by weight (approximately 3.5 litres per 25 kg bag). Application can be manual (trowel) or mechanized (pumps, extruders, etc.). Approximately 17 kg/m² of Sanalink for every centimetre of thickness to be implemented (approximately 1700 kg per cubic metre). Bag 25 kg

Sanaglass Binding, vitrifying, thick, syrupy solution of natural simple molecule minerals, for the production of insulating conglomerates, based on natural powdered cork, for ecological building interventions and in the restoration of vintage buildings and monuments. For use in combination with granulated cork conglomerates for: i) implementation of walkable subbase screeds for internal use; ii) as a covering of technical installations on interior slabs in homes. Reclaim and clean the application surfaces which must be compact and hardened, free from dust, fouling etc. Mix Sanaglass thoroughly and in-depth with granulated natural cork , for an amount of approximately 80-100 kg/m³ Place on site the adhesive conglomerate thus obtained, levelling it off on the reference marks with wood supports and then compacting it with a trowel. The mixing can be done manually, as well as with a normal cement mixer. In order to facilitate the application, it is possible to use the usual pumping devices. Sanaglass is perfectly compatible with any type of granulated natural cork. If it is used in combination with a granulated cork with a particle size of between 3-8 mm (as is usually available on the market), the consumption will be roughly 80 kg/m³ (coarser granulates require a lower consumption of vitrifying substances, however it will be much less effective both with regards to trampling and to thermal and acoustic insulation). In the case of using powdered cork (diameter 0-4 mm), the dosage of Sanaglass will be in the range 110-120 kg/m³. Binder function for natural light aggregates: from 80 to 120 kg per cubic metre of conglomerate with cork granulate. Approximately 120 kg/m³ with expanded perlite. Consolidating/anti-evaporation function: 0.25 kg per square metre of surface. Pallet tank (IBCs) 1350 kg - Plastic can 25 kg

Sanaxil P Breathable, natural, non-toxic paint, for external and internal surfaces, for adhesion and microcrystalline structure, based on stabilized potassium silicate. Mineral-based, active formulation, with high natural mildewcide and anti-condensation properties, prepared according to the traditional recipes, for use in ecological building interventions, new buildings and in the restoration of vintage buildings and monuments. Sanaxil P consists of potassium silicate and natural pigments. It has very high breathability, remarkable mildewcide and antibacterial properties. It has no solvents, thinners, harmful substances and toxic emissions in general, and does not have thermoplastic effects. Restoring and decorative paints for internal and external environments. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". Pre-existing paints (washable, organic, solvent based etc. ) must be thoroughly removed. Preliminarily treat the support with the fixative Sanaxil Fix. Apply Sanaxil P, using a brush, roller or spray, in the number of coats required by the absorption condition of the support. Sanaxil P is "dust-free" (it has started to be consistent to the touch) after about 1 hour. It can be overcoated after 4-6 hours, while it will be dry in-depth after 10-16 hours. Sanaxil P can be used as such or diluted with Sanaxil Fix, at a rate of 15-20% by weight. Apply from 0.30 to 0.40 liters of Sanaxil P per square metre of surface to be painted. Pail 4 l - Pail 14 l

Sanafarbe P Breathable, natural, non-toxic paint, for internal and external surfaces, diffusive type, based on lime putty. Mineral-based, active formulation, high natural anti-mildew and anti-condensation capacity, prepared according to the traditional recipes, for use in ecological building interventions and in the restoration of vintage buildings and monuments. Product based on lime putty and natural pigments. Sanafarbe P has a high breathability, remarkable mildewcide and antibacterial properties. It has no solvents, thinners, harmful substances in general. Decorative and internal and external restoration paint. The application supports will be free from fouling, powder, non-adhering parts, etc.; existing paints (washable, organic, solvent based etc.) must be removed. A preliminary fixative treatment of the surfaces is always advisable with a consolidating, transparent, Sanaxil Fix primer, based on potassium silicate. The application of Sanaxil Fix can be done by brush, roller or spray: the number of hands required and the dilution ratio with the most suitable water must be determined according to the conditions and absorption degradation of the supports. The admissible dilution range provides for water addition up to a maximum of 1:1 ratio. Apply by brush, roller, spray, in two coats, spaced-apart, one from the other, by about 24 hours. It allows the easy reproduction of traditional finish type: sponging, rubbing, marbling, infilling. Sanafarbe P is dry to the touch after 2 hours, it can be overcoated after 4 hours, while it will be dry in-depth after 8-16 hours. Apply from 0.20 to 0.40 liters of Sanafarbe P per square metre of surface to be painted. Pail 4 l - Pail 14 l

Sanatigh This macroporous, breathable, dehumidifying, fibre-reinforced plaster, with a base of natural hydraulic lime NHL 3.5, is for the dehumidification and hygrometric restoration of buildings and masonry, in works on green buildings, for new constructions and in the restoration of historic and monumental buildings. Sanatigh is a product consisting of hydraulic lime, botticino, kaolin, very fine calcium, expanded lightweight aggregates of volcanic origin, fiber-reinforced with special glass microfibres and fibers Readymesh PM 060. It has high hygroscopicity and breathability, contains no cements, resins, solvents and radioemissive substances. It has strong dehumidifying capacities and, thanks to the total absence of cement, is perfectly compatible with all types of masonry and especially with the historical walls and in all the interventions designed according to the canons of green building. Breathable dehumidifying plastering for wall bodies. Removal of crumbling plaster, if present, up to a maximum height of about 1 metre, with respect to the line of persistent humidity; wall bodies of application must in any case be clean, intact, dust-free, fouling, crumbling and non-adhering parts, conveniently saturated with water until they reach the condition of "saturated with dry surface". In the presence of salt efflorescence it will be necessary to ensure it is carefully removed by applying packs of the specific detergent and saline converter Deterg-A, in solution with water of 1:4. To prevent any new spills of salts, use specific universal anti-saline treatments in aqueous solution, Sanareg, for humid surfaces, or solvent-based, FEST SALZ, for cohesive saline concretions but with perfectly dry surfaces. PREPARATION OF THE WALL SURFACE • Remove all inconsistent, friable and rotten material, and grouting from joints, paying utmost attention where they are particularly friable or inconsistent (see also the paragraph on PREPARING SUPPORTS). • In case of strong salt concentrations, read the paragraph on PREPARING SUPPORTS. ROUGH COAT The sprayed rough coat must create a rough, corrugated surface to facilitate the adhesion of the following plaster, which must be applied promptly; within 1 - 2 days from the application of the rough coat. This adhesion spray must be applied with a low thickness (of a few millimetres) using a plastic-fluid consistency, and can be applied with the same Sanatigh product mixed with about 20% water. In case of particularly deteriorated masonry, it is recommended to use a specific Untersana product to make the rough coat. PLASTER The following application of Sanatigh must be made before the complete hardening of the rough coat (within 24-48 hours if the rough coat is made with Sanatigh, and 12-24 hours if made with Untersana). Put about 2/3 of the mixing water into the mixer, and then gradually add Sanatigh and the remaining water, continuing to mix into a homogeneous, lump-free mixture of the desired consistency for trowel or plastering machine application. Indicatively, the necessary mixing water is 16-18% by weight (i.e. 4 - 4.5 litres per 25 kg bag). Application can be performed by manual (trowel, plastering trowel) or mechanical spray methods. In case of application with a plastering machine, in order to allow adequate and homogeneous product mixing, it is recommended to not use machines with a continuous cycle, and to adjust nozzle, air and spray power in order to softly and lightly apply the product without excessive compaction. SKIMMING Levelling of plastered surfaces with Sanastof: green-construction fine, highly breathable mortar, natural hydraulic lime based with special, light, spherical micro-aggregates and high strength microfiber Readymesh PM 060. Protect surfaces from fresh direct exposure to sunlight, from the rain and wind. Cure the prolonged moist hardening. For thicknesses in excess of the 2 cm, and to improve the anti-cracking potential, provide for inserting a suitable reinforcement plaster-holding mesh: ARMAGLASS 140 o, recommended, a galvanized steel wire mesh with 2mm diameter, mesh 5x5 cm. Approximately 13 kg/m² of Sanatigh for every centimetre of thickness to be implemented (minimum thickness 2 cm = 26 kg/m²). Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Sanastof Bianco Premixed mineral composition based on natural hydraulic lime NHL 3.5, microsilic with pozzolanic activity, selected aggregates, high tenacity microfibers, light heat-insulating aggregates with low modulus of elasticity. It is used for smoothing and smoothing, both indoors and outdoors. It is perfectly compatible with multiple substrates: lime-based plasters, lime-cement, cement mortars, concretes, porous stone, bricks. Its characteristics make it particularly suitable for green building works and for the restoration of period and monumental buildings. The maximum grain size of the aggregate is 0.9 mm. Sanastof Bianco is a product based on natural hydraulic lime NHL 3.5, kaolin, marble dust, selected siliceous aggregates and light aggregates with a low modulus of elasticity, dimensionally stable. It is a natural product with high intrinsic breathability, without any trace of resins, solvents, diluents and radio-emissive aggregates. The product contains high tenacity microfibers which give great volumetric stability. The special rounded hollow aggregates, dimensionally stable, bring special qualities of thermal insulation, filtering of potentially harmful soluble salts and reduction of the elastic modulus to the shaving. The granulometric curve, the fineness of the binders and some rheological additives of natural origin, make the product particularly smooth during the drafting phase, even when laid on supports with rough or difficult surfaces. The calibrated physical-mechanical characteristics guarantee perfect compatibility on different types of substrates, especially on traditional plasters and mortars. The microsilic content with pozzolanic activity makes smoothing and smoothing performed with Sanastof Bianco highly durable, even in aggressive exposure environments. Quick and easy application on various substrates, such as: transpiring smoothing of wall casings; smoothing on modular wood fiber or calcium silicate coats; regularization of plastered surfaces; leveling of concrete surfaces; regularization and smoothing of repairs carried out with cement mortars; application to mainly thin thicknesses (from 1 to 4 mm) with simultaneous leveling of recesses, imperfections etc. In particularly severe operating conditions it is advisable to interpose, between the first and second coat, the alkali-resistant glass fiber mesh Armaglass 160 (the mesh must be partially drowned on the first still fresh coat of Sanastof Bianco). The breathability, combined with the other physico-chemical characteristics of the product, make the smoothing made with Sanastof an ideal support to accommodate any kind of paint and in particular mineral paints based on potassium silicate or slaked lime. Sanastof is the transpiring smoothing, with a low modulus of elasticity, recommended in all our dehumidifying systems made with the products: Sanatigh, Caleosana, Sanawarme, Unisan, Intosana. The application surfaces must be clean, free from dirt, crumbly and incoherent parts, dust, etc. Smooth substrates must be roughened (roughness> = 1mm). In the event that the support, after cleaning and roughening, is still dusty and crumbly, remove the totally incoherent parts dry with a spatula-brush, or assisting the removal operation with hydro-washing, then consolidate the support by impregnation with aqueous emulsion Protech Fix AC applied in two abundant coats, the second coat immediately before applying Sanastof Bianco with the "fresh on fresh" technique (the consumption of Protech Fix AC for this priming operation is between 120 and 250 gr / m2). Adequately wet the substrate with water before application, anticipating and repeating this operation several times in the case of very porous and absorbent substrates or in hot and arid climates. Approximately 1,3 kg/m² of Sanastof Bianco for each millimetre of thickness to be implemented (on average 3 - 3,5 kg per square metre). Bag 25 kg

Sanareg Non-film reactive liquid based on an alkylsilane emulsion dissolved in water to be used for the inhibition of saline efflorescence in the dehumidifying restoration of masonry, by spraying or applying with a brush with rigid bristles. Sanareg penetrates into the capillary pores of mineral substrates and reacts with the hydroxyl groups encountered in its path, forming an invisible water-repellent barrier that does not allow water to escape to the surface, leaving the transpiration to water vapor unaltered. Sanareg is an alkylsilane water emulsion, non-hazardous, non-toxic and VOC-free. The application of Sanareg does not alter the original wall breathability. Particularly indicated in combination with the cycle of natural dehumidifying plasters Untersana, Sanatigh and Sanastof. This also applies to Untersana, Caleosana and Sanastof. Non-film reactive liquid based on an alkylsilane emulsion dissolved in water to be used for the inhibition of saline efflorescence in the dehumidifying restoration of masonry, by spraying or applying with a brush with rigid bristles. Sanareg penetrates into the capillary pores of mineral substrates and reacts with the hydroxyl groups encountered in its path, forming an invisible water-repellent barrier that does not allow water to escape to the surface, leaving the transpiration to water vapor unaltered. Remove the soilings and saline manifestations by vigorous brushing; then eliminate any dust residue. Surfaces should be as dry as possible at the time of application. Apply Sanareg by spraying or with a long-bristled brush, proceeding from the bottom upwards. Remove any surface excess. When used as a preliminary treatment before a plastering cycle, apply the first coat of rendering immediately after applying Sanareg. Sanareg is water-based, which is why its effectiveness is not compromised even if the substrate is not perfectly dry at the time of application. From 0.10 to 0.20 kg of Sanareg for each square metre of surface to be treated, based on the porosity of the support. Plastic can 5 kg - Plastic can 25 kg

Sanafarbe I Natural, protective, decorative, breathable, pigmented, non-toxic putty coat, naturally mildewcide, based on hardened lime putty and botticino marble dust, for indoors and outdoors. Formulation prepared according to the traditional recipes, for use in ecological building interventions and in the restoration of vintage buildings and monuments. Product based on lime putty and natural pigments. SANAFARBE putty coat has a high breathability, a remarkable mildewcide and antibacterial capacity. It has no solvents, thinners, harmful substances in general. Embodiment of putty coat finishing, protective and decorative, internal and external masonry building, in ecological building interventions and in the restoration of vintage buildings and monuments. The application supports will be free from fouling, powder, non-adhering parts, etc.; existing paints (washable, organic, solvent based etc.) must be removed. Spread Sanafarbe I, into two coats: the first, by simple deposition, with steel trowel, the second for laying and finishing, with sponge float. The application of the second coat must be carried out, when the first coat starts to dry, in one of two conditions suggested: with dry trowel, for smooth surfaces, with moistened trowel, for antique-effect surfaces. SANAFARBE-I is dry to the touch after 4 hours, it can be overcoated after 2-5 hours, while it will be dry in-depth after 16-32 hours. Indicative consumption depending on the different particle sizes of Sanafarbe I available: 1 mm GRAIN: approximately 1.6 -1.8 kg/m²; 1.2 mm GRAIN: approximately 1.8 -2.0 kg/m²; 2 mm GRAIN: approximately 2.4 -2.8 kg/m²; 2.2 mm GRAIN: approximately 2.6 -3.0 kg/m². The indicated yields refer to smooth supports and are for guidance only. Actual consumption must be identified with a suitable practical test. Pail 5 kg - Pail 25 kg

Untersana With the addition of mixing water only, this single-component premix creates a breathable, dehumidifying rough coating, preparatory to the application of restorative, dehumidifying, thermal-insulating and anti-condensation plasters, specifically Intosana, Sanatigh, Sanawarme and Caleosana, being plasters designed specifically for the healthiness of new buildings, existing buildings, works on green buildings and in the restoration of historic and monumental buildings. Untersana is composed of hydraulic lime, botticino, kaolin, calcium caseinate, Vichy salt, tartaric acid and natural fibres. Does not contain cements, resins, solvents, thinners and radioemissive aggregates. Anchoring scratch coat (applied by "spraying" or "splashing") for the formation of an adhesive bridge for easy grip of subsequent plasters, dehumidifying, breathable, based on hydraulic lime. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". Pour about 2/3 of the mixing water into the mixer, add Untersana and the remaining water; continue to mix until a homogeneous lump-free mixture is obtained. The mixing water should be about 22-25% of the weight of the bag. After mixing is completed wait a few minutes before applying. "Spray" the product, with plastic fluid consistency, on the application supports, with plastering trowel and brick trowel or with plastering pump. Protect fresh surfaces from direct exposure to sunlight, from the rain and wind, cure the prolonged moist hardening. From 4 to 6 kg of Untersana per square metre of surface to be rendered. Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Unisan A composite mortar that is fibre-reinforced, consolidating, dehumidifying, grey in colour and utilised for the structural restoration of crumbling old or monumental masonry. It contains no substances that are potentially harmful to masonry and is composed of NHL 3.5 natural hydraulic lime and hydraulic binders free from soluble salts, along with silicas with pozzolanic activity, selected siliceous-calcareous aggregates, specific shrinkage-reducing agents and resistant alkaline READYMESH fibres that confer high flex-traction whilst increasing the performance of the mortar’s fracture energy. In conjunction with ARMAGLASS STRUCTURA fibreglass mesh, it is ideal for the structural restoration of old walls or crumbling constructions. Construction of plasters and reinforced slabs in interventions of restoration, construction of plaster and dehumidifying coatings with high performance, bedding of bricks and modular elements. The surfaces should be clean and free of any soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition of "saturated dry surface". In the case of structural reinforcing slabs, you will need to proceed with applying an appropriate reinforcing electrowelded mesh, to be fixed with PROFIX, Grout Micro-J, Repar Tix G2 or Syntech IC 55. Pour about 2/3 of the mixing water into the mixer, add Unisan and the remaining water; continue to mix until a homogeneous lump-free mixture is obtained. The mixing water should be about 12-14% of the weight of the bag. After mixing is completed wait a few minutes before applying. Apply the product by plastering trowel and brick trowel, or preferably with plastering machine (type PFT model G4). Do not apply in case of direct exposure to sunlight or excessive ventilation. Cure the protection and the prolonged moist hardening, of exposed surfaces. Approximately 15 kg/m² of Unisan for every centimetre of thickness to be implemented (approximately 1500 kg per cubic metre). Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Sanadek Breathable, natural, non-toxic paint, for internal use, diffusive type, based on long hardening lime putty, prefiltered. Mineral-based, active formulation, high natural anti-mildew and anti-condensation capacity, prepared according to the traditional recipes, for use in ecological building interventions and in the restoration of vintage buildings and monuments. Product based on lime putty and natural pigments. Sanadek has high breathability, it has remarkable mildewcide and antibacterial properties. It has no solvents, thinners, harmful substances in general. Decorative and interior renovation paint. The application supports will be free from fouling, powder, non-adhering parts, etc.; existing paints (washable, organic, solvent based etc.) must be removed. A preliminary fixative treatment of the surfaces is always advisable with a consolidating, transparent, Sanaxil Fix primer, based on potassium silicate. The application of Sanaxil Fix can be done by brush, roller or spray: the number of hands required and the dilution ratio with the most suitable water must be determined according to the conditions and absorption degradation of the supports. The admissible dilution range provides for water addition up to a maximum of 1:1 ratio. Apply by brush, roller, spray, in two coats, spaced-apart, one from the other, by about 24 hours. Apply from 0.30 to 0.40 liters of Sanadek per square metre of surface to be painted. Pail 4 l - Pail 14 l

Calcesana Nocciola Natural hydraulic lime, hazel-coloured, obtained through firing, in a vertical oven in refractory stone and bricks, at temperatures of 1100°C, of constant quality select marly limestones, specific for mortars, plasters and substrate screeds in ecological building works and in interventions of historical and monument restoration. Calcesana Nocciola is the result of a firing process which, due to the inherent properties of the furnace, and to stringent controls, takes place at temperatures of 1100°C. Calcesana Nocciola is reduced to a very fine powder with traditional grinding processes unchanged over time. Calcesana Nocciola confers remarkable breathability properties to mortars and plasters, as well as outstanding characteristics of resistance to chloride penetration and corrosion from sulphate waters, even with high values of free carbon dioxide. Calcesana Nocciola is characterised by low soluble salt content, by the total absence of cement and chemical additives, and by its high inhibiting power against bacteria and biodeteriogenic settlements (moulds etc.). Calcesana Nocciola is used in the preparation of mortars for masonry and internal and external plasters on site. Extend mixing times for at least 5'. Apply on supports saturated with water, with dry surface. Do not add chemical additives without consulting our Technical Service first. Cure the convenient and prolonged moist hardening of fresh mortars and plasters. Protect the fresh mortars and plasters from direct exposure to the sun and ventilation. From 250 to 450 kg of Calcesana Nocciola for each cubic meter of dough to be made. Packaging: 25 kg bag UM: €/kg

Grout Fill An anti-shrinkage, pourable, self-levelling, super-adhesive micro-mortar, based on high-strength cements, super-pozzolanic fillers, polymeric stabilisers and anti-shrinkage agents. Aggregates with a maximum size of 0.35 mm. Ideal for filling joints (gaps and/or interstices) in urban paving made of porphyry or stone slabs, even of large dimensions. For filling cracks and lesions on concrete and masonry structures. Grout Fill achieves fluid and hyperfluid workability even with very low water / cement ratios (<0.4), thus resulting perfectly homogeneous, pourable, self-leveling and without water exudation phenomena. The very fine granulometry of the aggregates allows the perfect filling of spaces and particularly narrow discontinuities (<0.5 cm). The capillary absorption of the applied micro-mortar is very low, allowing great resistance to freeze-thaw cycles and washout. Grout Fill achieves extremely high mechanical performance and is rich in microsilicates with pozzolanic activity and special additives that make it extremely durable even if positioned in particularly aggressive environments (due to contamination by chlorides, sulphates, marine atmospheres, fuels and automotive oils). Filling the joints (vanishing points) in urban floorings in porphyry, stone slabs etc., in new installations and in the reinforcement of existing installations. Anchorages and rigid seals in general. Remove the soilings, the crumbling and non-adhering parts and saturate beforehand with water. Pour about 2/3 of the required mixture water in the mixer (about 3.5 -4 litres total per bag); gradually add the product and the water still required to get the desired consistency. Continue mixing until you obtain a homogeneous, lump-free mortar. Pour the compound thus obtained in the vanishing points to be filled. Approximately 1800 kg of Grout Fill for each cubic metre of volume to be filled. Packaging: 25 kg bag Unit of Measure: €/kg

Il profumo microincapsulato al cocco offre un'esperienza olfattiva esotica e avvolgente, perfetta per chi ama le fragranze dolci e tropicali. Questo profumo cattura l'essenza cremosa e calda del cocco, evocando sensazioni di vacanza e relax. Grazie alla microincapsulazione, il profumo viene rilasciato gradualmente, garantendo una lunga durata e un'esperienza olfattiva costante. Ideale per profumare ambienti domestici o spazi commerciali, il profumo al cocco aggiunge un tocco di dolcezza e calore.

Il profumo microincapsulato ai frutti di bosco è una scelta eccellente per chi ama le fragranze dolci e fruttate. Questo profumo cattura l'essenza succosa e vibrante dei frutti di bosco, offrendo un aroma che è al contempo fresco e accattivante. Grazie alla tecnologia di microincapsulazione, il profumo viene rilasciato gradualmente, garantendo una lunga durata e un'esperienza olfattiva costante. Ideale per profumare ambienti domestici o spazi commerciali, il profumo ai frutti di bosco aggiunge un tocco di freschezza e vivacità.

Il profumo microincapsulato ai frutti tropicali offre un'esperienza olfattiva esotica e avvolgente, perfetta per chi ama le fragranze dolci e tropicali. Questo profumo cattura l'essenza vibrante e solare dei frutti tropicali, portando una ventata di freschezza in qualsiasi ambiente. La tecnologia di microincapsulazione garantisce un rilascio graduale del profumo, mantenendo l'ambiente profumato per lungo tempo. Ideale per l'uso in case, uffici o negozi, il profumo ai frutti tropicali crea un'atmosfera accogliente e stimolante.

Il profumo microincapsulato all'ananas porta con sé l'essenza esotica e dolce di questo frutto tropicale, trasformando qualsiasi ambiente in un'oasi di freschezza. L'aroma vivace e fruttato dell'ananas è perfetto per chi desidera un profumo che evochi sensazioni di vacanza e relax. La microincapsulazione assicura che il profumo venga rilasciato lentamente, mantenendo l'ambiente profumato per un periodo prolungato. Questo profumo è ideale per l'uso in case, uffici o negozi, dove può creare un'atmosfera accogliente e invitante.

Il profumo microincapsulato alla fragola è una scelta eccellente per chi ama le fragranze dolci e fruttate. Questo profumo cattura l'essenza succosa e vibrante delle fragole, offrendo un aroma che è al contempo fresco e accattivante. Grazie alla tecnologia di microincapsulazione, il profumo viene rilasciato gradualmente, garantendo una lunga durata e un'esperienza olfattiva costante. Ideale per profumare ambienti domestici o spazi commerciali, il profumo alla fragola aggiunge un tocco di freschezza e vivacità.

Il profumo microincapsulato alla frutta secca offre un'esperienza olfattiva ricca e avvolgente, perfetta per chi ama le fragranze calde e nutrite. Questo profumo cattura l'essenza ricca e complessa della frutta secca, evocando sensazioni di comfort e calore. Grazie alla microincapsulazione, il profumo viene rilasciato gradualmente, garantendo una lunga durata e un'esperienza olfattiva costante. Ideale per profumare ambienti domestici o spazi commerciali, il profumo alla frutta secca aggiunge un tocco di eleganza e raffinatezza.

Il profumo microincapsulato al kiwi offre un'esperienza olfattiva fresca e fruttata, perfetta per chi ama le fragranze leggere e rinvigorenti. Questo profumo cattura l'essenza vibrante e succosa del kiwi, portando una ventata di freschezza in qualsiasi ambiente. La tecnologia di microincapsulazione garantisce un rilascio graduale del profumo, mantenendo l'ambiente profumato per lungo tempo. Ideale per l'uso in case, uffici o negozi, il profumo al kiwi crea un'atmosfera accogliente e stimolante.