Termékek a csomagolás (365)

Gas hand tool for thermo shrinking Hornet, high power (until 90 Kw), but very light and handy with practical handle with fast lever gas and electronic ignition. The high power and ease of use allow a fast shrinking of plastic films of each thickness and the realization of packaging even large. Raptor it's available with power of 70 Kw and 90 Kw. The main areas of application are: Packing : Welding / retraction of packaging also large Boating : Realisation of coverages in plastic film for boat storage Building : Welding and retraction of plastic film for protective scaffolding Environment : Welding of plastic film for coating for containment tanks Example model:FP HORNET 70 Power :70 Kw. - 238.800 btu/h Supply :propane gas Max. pressure :4 bar Consumption :5,22 Kg/h Ignition :piezoelectric

ME-CFE CONSTANT AUTO SEALERS WITH MOTOR CONTROL Table top motorized sealer with electric pedal and welding bars at a constant temperature for sealing polypropylene bags and paired/laminated aluminium, paper, barrier materials, etc. The sealing bars of the type "hot bar" are equipped with resistance and thermostat for controlling the temperature from 30 ° C to 250 ° C. The closure of the bars it takes place through an engine which guarantees a high welding pressure (0,7 Kg./cm2) and allows the sealing of envelopes with hight tickness with or without side bellows. Operation The operation provides for the closure of bars and seals the bag following operator control, by electric pedal. This allows the operator to grab the bag with both hands, being able to perform a more precise sealing and parallel to the bag. Seal length:mm. 300/400 Seal width :mm. 14 Temperature:80°÷250°C

Impulse sealer with mechanical pedal and floor support for the closure of bags in plastic material heat-sealable, impulse sealing (resistance to heat for a few seconds) and timer for adjustment. At the end of the sealing is possible to trim the bag with the cutter installed on the bar. The open structure also allows you to install a coil on the back of the machine and to obtain envelopes of the desired length using the tubular film. The sealing head can be tilted up to 45 ° to allow the closure of the envelopes containing liquids or powders. Maximum thickness of 0.15 mm sealable . (0.30 mm. Overall) Max. seal length:mm. 450/mm. 600 Seal width:mm.2 Thermosealing materials:PE-PP

MG 1020 SEALING MACHINE WITH CLOSING MAGNET Pulse sealers MG 1020 series, with 1020 mm sealing bar and suitable for sealing polyethylene, pvc and polypropylene bags. They have a special timer for adjusting the sealing time based on the thickness and type of material. The MG sealers are complete with a manual cutting unit for the trimming of the sealed bags and/or the creation of bags from tubular reels (if the machine is equipped with a roll holder). The sealing bars must be closed manually by the operator and are automatically held by a magnet until the end of the cycle. There are special supports with mechanical pedal, for the manual sealing machine and with electric pedal for the sealing machine with motorized bar closing. Available models: MG 1020: bench sealing machine with manual closing of the bars MGMI 1020: bench sealing machine with motorized closing of the bars and electric pedal Max. seal length:mm. 1020 Seal width:mm. 5 Max. seal thickness:0,20 mm (0.40 tot)

Pneumatic tensioner model FP LASH very powerful and easy to handle, suitable for all working conditions, guarantees a high tensile strength and it is suitable for securing bulky and heavy loads on trucks, containers, ships, etc. The high tension force (7500 N) allows the use of textile strap with width up to 50 mm. It is also possible to adjust the tension acting on the supply pressure. The holding capacity of strap depends on material type and on strap of choice. Strap width:Max 50 mm Tension:Max 7500N Weight:4,5 Kg

Le incappucciatrici Bocedi sono costruite con un’esperienza pluriennale e costantemente aggiornate negli anni per soddisfare i nuovi standard di marcato. Sono macchine progettate per automatizzare la fase di incappucciamento di fine linea e sono disponibili in due versioni differenti. Le incappucciatrici lavorano con film termoretraibile tubolare, che viene srotolato automaticamente e tagliato su misura del pallet da incappucciare grazie ad un sistema di riconoscimento automatico del carico. Il cappuccio viene poi messo a copertura del carico senza entrarne in contatto, per garantire stabilità anche ai carichi più fragili e delicati. Vari formati di pallet Le incappucciatrici posso essere configurate da 1 a 6 bobine diverse di film, in taglia o spessore, offrendo la possibilità di incappucciare vari formati di pallet in un’unica macchina. Cappuccio elastico tagliato su misura La dimensione dei pallet viene identificata automaticamente Capacità:fino a 240 pallet/ora Dimensioni minime pallet:400×400 mm Dimensioni massimepallet:1350×1250 mm

The semi-automatic strapping machines are ideal for tying boxes, packages, bundles, etc. in warehouses, workshops, supermarkets and anywhere there safe packing is needed. The plastic strap helps to reinforce the packaging and ensure ligation. The printed strap is also available. If placed around the packaging, the strap is a valuable burglar resistant tool, if the package is opened it can not be closed with the same type of strap. The model FP8022 allows to strap the product with minimum size of 60x60x10 mm and it uses strap with width 6-9-12 mm and with max thickness of 0,6 mm. Strap width:mm. 6- 9- 12 Strap thickness:mm. 0,5-0,6 Air pressure:6/7 bar Air consumpt:12 Lt. / sec Weight:85 Kg

Veline

Pneumatic strapping tool with vibration welding (heating by friction) for straps in polyester PET width 16-19 mm and max. thickness mm. 1,27. Compact, handy, easy to use, is suitable for closing all kinds of flat packaging. Thanks to a very short base and the command of reverse rotation of the roller it may also strap round packing with a minimum diameter of mm. 700. The operator simply inserts the two overlapped strips into the strapping tool, press a button to make the tension, a second button to get the vibration welding, and at the end a third button to pull out the tensioning device effortlessly. Strap width:from 16,0 to 19,0 mm. Strap thickness:0,80-1,27 mm. Air pressure:6 bar Air consumpt:12 Lt. / sec Weight:5,3 Kg

Semiautomatic mobile strapping machine for the strapping of pallets, complete with a channel for inserting the strap. New compact model with closed body and internal reel holder. Hinged raceway equipped with double roll to facilitate the insertion of the strap into the base of the pallet. Strapping sling channel with containment flaps (avoiding the exit of the strap). Electronic voltage regulation via potentiometer. Electronic regulation of the strap throw length. Safety function with acoustic alarm and tension delay (when the operator inserts the strap he has time to remove the hand). Strap width:mm. 12 Strap thickness:mm. 0,6 - 0,65 Reel internal diameter:mm. 200 Power supply:220 V 3 phase Weight:80 Kg

Pneumatic strapping tool with vibration welding (heating by friction) for straps in polypropylene PP and polyester PET width 13-16-19 mm and max. thickness mm. 0.9. Compact, handy, easy to use, is suitable for closing all kinds of flat packaging. Thanks to a very short base and the command of reverse rotation of the roller it may also strap round packing with a minimum diameter of mm. 700. The operator simply inserts the two overlapped strips into the strapping tool, press a button to make the tension, a second button to get the vibration welding, and at the end a third button to pull out the tensioning device effortlessly. Strap width:from 13.0 to 19.0 mm. Strap thickness:0,40-0,90 mm. Air pressure:6 bar Air consumpt:14 Lt. / sec Weight:4,9 Kg

Place the pallet on the platform and hook the stretch film to the base then press the start button. The platform begins to rotate, after 2-3 turns operate the button for coil ascent. After reaching the desired height, stop the lifting of the reel and after 2-3 turns stop the machine or operate the descent of the reel and carry out the winding up to the base of the pallet. At the end of wrapping, press the stop button and cut the film. On request we can produce wrapping machines with: Rotary table diameter mm. 1800 - 2000 Electronic scale integrated STRETCH FILM FOR WRAPPING MACHINES: The film normally used on winding machines is 23 my standard in rolls of approximately 16 kg. With 1 roll of film you are able to wrap an average of 60 pallets. The film is also available in white 30 my, suitable to protect the contents of the pallets from sunlight. The white film is opaque and can be used to hide valuable goods during transport. Maximum load:Kg. 2000 Max pallet height:mm 2200 h (2400 mm with optional) Turntable diameter:mm. 1500 Height of turntable:mm. 75

The semi-automatic strapping machines are ideal for tying boxes, packages, bundles, etc. in warehouses, workshops, supermarkets and anywhere there safe packing is needed. The plastic strap helps to reinforce the packaging and ensure ligation. The printed strap is also available. If placed around the packaging, the strap is a valuable burglar resistant tool, if the package is opened it can not be closed with the same type of strap Strap width:mm. 5 – 9 – 12 Strap thickness:mm. 0,5-0,6 Air pressure:6/7 bar Air consumpt:12 Lt. / sec Weight:100 Kg

La carta Specchio è un incarto di alta qualità capace di mantenere la freschezza del prodotto più a lungo grazie allo strato di polipropilene metallizzato che protegge dai raggi UV e dall’umidità. Ideali per alimenti freschi come salumi, formaggi, prodotti gastronomici. Sia la carta che i sacchetti, accoppiati, possono essere facilmente disgiunti e separare quindi carta da plastica, favorendo la raccolta differenziata e l’ambiente. La superficie,” a specchio ” esalta la visibilità del prodotto oltre ad allungarne la shelf-life. Inoltre i sacchetti possono essere anche termosaldati garantendo quindi una chiusura ed un trasporto del contenuto adeguato e sicuro. Idoneità totale al contatto alimentare.

Pneumatic tensioner model FP CORD for tensioning and cutting of polyester strap textile and composite. Equipped with high tension force (7500 N) allows the use of strap widths up to 32 mm. By acting on the supply pressure it is possible to adjust the tension. The built-in knife allows cutting the strap easily and without waste of material. The holding capacity of strap depends on material type to strap and on strap choice. Strap width:Max 32 mm Tension:Max 7500N Weight:3,8 Kg

Self-propelled battery wrapper, suitable for wrapping with stretch film pallets with a maximum height of mm. 2050, also with an irregular shape. However, the base of the pallet must have a regular shape to allow the feeler wheel to follow its shape. Rotating automatically around the pallet, it wraps with stretch film or net. Equipped with rudder for manual steering with forward-reverse buttons, maintenance-free gel traction batteries, built-in battery charger, three-phase electric motors with inverter, height-adjustable guide wheel, front safety bumper. The FP GLOBO model is equipped with a folding arm with reel holder trolley.Keyboard lock Rotation speed adjustable from 5 to 12 rpm Up/down reel carriage speed from 1.3 to 5.4 m/min Turns at the base/top of the pallet from 1 to 10 Pallet height reading delay Film tension adjustment Film pre-stretch adjustment Reel change comfort cycle CYCLES SELECTABLE FROM Weight:Kg. 300 Overall size:mm. 1280x1850x1000h

MG 300 SEALING MACHINE WITH CLOSING MAGNET Impulse sealers MG 300 series, with 300 mm sealing bar and suitable for sealing polyethylene, pvc and polypropylene bags. They have a special timer for adjusting the sealing time based on the thickness and type of material. The MG sealers are complete with a manual cutting unit for the trimming of the sealed bags and/or the creation of bags from tubular reels (if the machine is equipped with a roll holder). The sealing bars must be closed manually by the operator and are automatically held by a magnet until the end of the cycle. There are special supports with mechanical pedal, for the manual sealing machine and with electric pedal for the sealing machine with motorized bar closing. Maximum weldable thickness 0.15 mm (0.30 tot). Available models: MG 300: bench sealing machine with manual closing of the bars MGM 300: bench sealing machine with motorized bar closing and electric pedal Max. seal length:mm. 300 Seal width:mm. 3 Max. seal thickness:0,15 mm (0,30 tot)

The DSL professional inkjet marker is suitable for marking on porous surfaces (cartons, cartons). Thanks to the external ink tank, it is possible to position the marker on automatic lines and save considerably on consumables and cartridge replacement times. The cartridges contain 420 ml. The cost of printing is about 5 times lower than the other FPA2 series markers. It allows to print alphanumeric texts, logos, date / time, codes, counter, lot and 1D & 2D barcode, distributed on different lines with a total height of 12,7 mm. The minimum printing height is about 5,4 mm. The marking speed can be set directly on the marker keypad and it is therefore possible to write accurately and without deformation of the characters. The cartridges are very durable, have a duration of tens of thousands of markings and do not require maintenance. The marker is however equipped with an automatic nozzle cleaning system. Thanks to the SD card (included in the package) you can save up to 999 messages. Resolution:600x300 dpi based on resolution and printing speed Print engine:Hewlett-Packard Thermal Ink Jet Technology Print speed:72 m/min at 300 dpi, horizontal resolution Maximum printing height:12,7 mm (1 row) Minimum printing height:2,7 mm (on several lines) Print distance:6 mm recommended Printable elements:alphanumeric writings, logos, date / time, codes, counter, lot and barcode

PNEUMATIC CLIPPER FOR GABIONS Large sturdy pneumatic clipper with ring closure, using clips of 45 mm. with wire diameter 3 mm. and can close up to a diameter of 15 mm (mm. 13 for model FPPS45P-13). Suitable for the assembly of the containment gabions in mesh, structures and fencing in wire mesh, fixing reinforcements for the building, sealing bags or mattresses that are used as retaining walls, sound barriers, dikes, road reinforcements, reinforcement of banks, horticulture, traps and rockfall protections. Structure :Steel with rubber handle Charger capacity:100 rings Open ring width (outer):mm 45 Open ring height:mm 24 Opening width:mm 25 Working pressure:5-6 bar Closure internal diameter:mm 15 (mm 13 for model FPPS45P-13)

Valvola a sfera 2 vie lucida, acciaio inox AISI316, con guarnizioni in PTFE vergine, filettata F/F con attuatore elettrico.

To be installed at the exit of the packaging machines and welding machines. ROTATING TABLE OF ACCUMULATION WITH STAINLESS STEEL STRUCTURE AND NYLON PLAN The rotary table of accumulation is generally used in the final part of the packaging lines and facilitates the discharge of the packs, facilitating the sampling operations by the operator. The rotating tables with nylon plan are available with a diameter of 800, 1200 or 1400 mm, and are suitable for bottles, cans and products that can overturn in the concave or convex turntables. The flat rotating tables can be equipped with loading systems and automatic unloading and thus be used as "accumulation areas" between an automatic machine and another. Edges and sides nylon version Flat turntable with holding sides, polyethylene plan, useful height of 810 mm and a mechanical speed variator. Table top diameter:mm. 800 - 1200 - 1400 Installed power:Kw. 0,18 Standard height of the plan:mm. from 770 to 850

Wrapping machine semi-automatic with turntable mod. FP BOX - TIRES, suitable to the winding of tires coupled with internal diameters from 300 mm to 500 mm. The rotation of the table is motorized, activated by the pedal and with adjustable speed; the movement of ascent / descent coil is manual with reel holder counterweighted. The machine is equipped with the compressed air device by drive via lever valve for centering and locking of the wheels, consisting of two jaws which are installed on the expansion of extractable pins. To lock and unlock the tires is sufficient to drive the valve lever. The group expansion is raised by about 150 mm. from the plane table. Load:200 Kg Internal tyres diameter:da mm. 300 a 500 (adjustable) Turmtable diameter:Max mm. 1000 Max package dimensions:mm. 800 x 800 x 1000 h Height from the floor:mm. 700 Power:Kw 0,37 Weight:200 Kg Dimensions:1600x1000x1800 h

Busta con cursore

Semiautomatic bench heat sealers with timer and trimming for bags in PE PP and l - Semiautomatic impulse heat sealers for the bench, for closing PE, PP, PVC and light coupled bags. Equipped with timer, pedal and trimmer. They can be used for: food products, in the automotive, cosmetics, electronics, mechanical and plastic parts, packaging for e-commerce, pellets and agriculture and for chemical products. Available in 460mm and 610mm welding lengths, and 4mm high. Suitable for bags of different thickness, with moist or dusty contents. Double sealing bar with separate regulation of temperatures and times. Manual and semi-automatic operation with electromagnetic closure. Adjustment of the welding power by means of a 6-position switch. Activation by electric pedal or automatic cycle button with digital control of the welding parameters. Digital timer with LCD, for precise control of welding (0-10 sec.) And cooling (0-20 sec.) Times. Can be combined with dosing systems.

Latest generation machine suitable for RESTAURANTS, BUTCHERS, FOOD INDUSTRIES, TRACTORIES and wherever there is the need to vacuum pack both solid and liquid products The AUTOMATIC product recognition system allows you to switch from one production to another without having to change settings. Cooks who work in the kitchen know very well how problematic it is when multiple colleagues have to use the same machine and package different products The color keypad is extremely functional and allows you to change program and vacuum percentage in just a few seconds. Extremely easy to clean vacuum chamber and raised suction. Example model:FP41 RISTO SMART Bar type:1 front mm 410 Machine type:bench Chamber dimensions:mm 417x450x220H (100+120) Vacuum pump: 25 m3/h Num nozzles (gas option):2 Max. bags size:mm 400x500

Busta con cerniera a pressione e gancio saldato

The SMART inkjet marker is the simplest professional model in the series. It allows printing up to 12.7 mm on porous surfaces (boxes, cases, etc.). It allows to print alphanumeric texts, logos, date/time, codes, counter, lot and 1D & 2D barcode, distributed on different lines with a total height of 12.7 mm. The minimum printing height is about 5.4 mm. The marking speed can be set directly on the marker keypad and it is therefore possible to write accurately and without deformation of the characters. The cartridges are very durable, have a duration of tens of thousands of markings and do not require maintenance. Following tests, unlike other cartridges, they proved to be working even after leaving them uncovered for weeks. The marker is however equipped with an automatic nozzle cleaning system. Thanks to the SD card (included in the package) you can save up to 999 messages, setting them in any size (maximum 12,7 mm) and any Word font format. Resolution:600x300 dpi based on resolution and printing speed Print engine:Hewlett-Packard Thermal Ink Jet Technology Print speed:72 m/min at 300 dpi, horizontal resolution Maximum printing height:12,7 mm (on 1 row) Minimum printing height:2,7 mm (on several rows) Print distance:6 mm recommended

Impulse sealers MG 621 series, with 620 mm sealing bar and suitable for sealing polyethylene, pvc and polypropylene bags. They have a special timer for adjusting the sealing time based on the thickness and type of material. The MG sealers are complete with a manual cutting unit for the trimming of the sealed bags and/or the creation of bags from tubular reels (if the machine is equipped with a roll holder). The sealing bars must be closed manually by the operator and are automatically held by a magnet until the end of the cycle. There are special supports with mechanical pedal, for the manual sealing machine and with electric pedal for the sealing machine with motorized bar closing. The MG 621 series sealing machines are available with mechanical or motorized closing bars with 3 or 5 mm sealing thickness depending on the model. Also available in stainless steel with mechanical closure of the bars and and 3 mm sealing. Model:MG 621 Max. seal length:mm. 620 Seal width:mm. 3-5 Power:750W Dimensions:cm. 76x20x27 Weight:Kg. 21

Semiautomatic table top sealer with electric pedal and impulse sealing bar (resistance is heated for a few seconds), suitable for closing bags of plastic material heat-sealable. The closing of the sealing bars by pressing the pedal electric with solenoid allows the operator to have both hands free and for increased production, just select the automatic cycle with timed closure. The timers for adjusting the welding and cooling ensure maximum reliability of each type of material. Simple to use, requires no preheating. Maximum thickness. weldable 0.20 mm. (0.40 mm. Overall) Example model:ME 355 AI Sealing bar lenght:mm. 350 Sealing width:mm. 5 Weldable materials:PE-PP Max thickness weldable:0,20 mm (tot 0,40 mm)

Le Navette Bocedi sono un accessorio indispensabile quando il carico deve essere trasferito automaticamente da/per la linea di imballaggio. Le navette hanno dimensioni personalizzabili e possono essere facilmente integrate in impianti già esistenti.