Termékek mould gyártók uk (33)

Silicone Molds

Grout CR Composite , castable, anti-washout, controlled shrinkage cement mortar, superfluid consistency, based on high-resistance cements, superpozzolanic fillers (MICROSIL 90), polymeric modifiers, shrinkage resistant agents, specific additives, calcium silicate mineral fibres, selected silica aggregates. - Based on of thickened silica fume - three-dimensionally reinforced fibre with mineral and synthetic fibres - Provides high adherence and adhesion - dimensionally stable (shrinkage-compensated) - Provides high stability-physical chemical and resistance to chlorides and sulphates - suitable for underwater castings: it is anti-washout - high strength in terms of hydrostatic positive and negative thrust. Repair and protective coatings of hydraulic structures, marine and underwater structures, and articles in critical situations: harsh chemical-physical, leaching water, marine atmosphere, etc. Filling of formwork for the containment of cast immersed in sea water. In case of underwater application, the installation operations must be carried out within 8-10 hours of cleaning and "fouling" (accumulation and deposits of organic and inorganic particles on product surfaces) removal. An adequate roughening of the surfaces by scarifying, sandblasting etc. is always necessary in order to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). Pour 2/3 of total mixture water in the cement mixer, gradually add the product and the remaining water, until a homogeneous mixture of the required consistency is obtained. For sizable filling thicknesses, greater than 60 mm, Ghiaietto 6.10 (inert washed is selected with a particle size of from 6-10 mm) can be added in a percentage ranging from 20% to 40 %, on the basis of practical requirements. In some particularly demanding cases in terms of the resistance to the "dry-wet" cycle (for example, for the action of the tides) or for chemical attacks particularly strong, it would be advisable to add, in addition to the gravel, even thickened silica fume(MICROSIL 90), and in a variable amount depending on the thickness and construction-related need, to further improve the waterproofing and the mechanical strength of the product. In these cases, please contact our Technical Service. In the case of casts in water, make sure of perfect product hardening before removal of the formwork. Approximately 20,50 kg/m² of Grout CR for every centimetre of thickness to be implemented (approximately 2050 kg per cubic metre). Packaging: 25 kg bag UM: €/kg

CALDOS DE POLLO, TERNERA, GAMBA, VEGETAL, CORDERO en PASTILLAS 10 GR HALAL

Shisha charcoal incense charcoal hookah charcoal Dutch charcoal are one of the best pure smoking charcoal With high quality and standard.

Together with the Fachhochschule Münster – University of Applied Sciences we are working on ALWA PERM (patent No. 2583995). This is a metal-filled casting resin for producing a porous, resin-bound mould. These materials are applicable in the areas of thermoforming, the ceramic industry, intake moulds and devices, pneumatic cushioning, the filter industry, etc. ALWA PERM allows a castable production of porous metallic materials with a binder for the first time. The system offers a highly accurate mould surface reproduction. The profile characteristics goes far beyond the current state of the art. NO MORE DRILLING OF VACUUM HOLES! NO DAMAGE OF THE MOULD SURFACE DUE TO DRILLING HOLES

Shisha charcoal incense charcoal hookah charcoal Dutch charcoal are one of the best pure smoking charcoal With high quality and standard.

Anwendung: Verfugen von Geraden, Schamottefliesen in Kachelöfen, Kaminen, Öfen, Gartengrills. Die empfohlene Fugenstärke beträgt 2-3 mm. thermischer Widerstand:1300 °C Verpackung:5 kg Gewicht (kg]:25.0000 Artikelnummer:9005249005862

Erhalten Sie komplexe 3D-gedruckte Bauteile mit Geometrien in wenigen Tagen. - 3D-Druck oder Additive Fertigung (AM) bezeichnet verschiedene Verfahren zur Herstellung von dreidimensionalen Objekten nahezu beliebiger Formen. Bei RPWORLD ist der additive 3D-Druck für funktionale Prototypen, komplexe Designs und Herstellungskomponenten konzipiert. Materialauswahl Selektives Lasersintern (SLS), Stereolithographie (SLA) und Fused Deposition Modeling (FDM) sind die gängigsten Additive Fertigungsverfahren, die RPWORLD zur Realisierung von Projekten einsetzt. Kosten-effizient Sie können die 3D-gedruckten Teile in beliebigen Formen nach Ihren Wünschen erhalten. Und noch wichtiger ist, dass aufgrund des Verzichts auf Formen ein kosteneffizienter Prozess für Ihre individuellen Teile entstehen kann. Komplexe Geometrien Die Struktur der 3D-gedruckten Teile ist nicht begrenzt. Sie können nahezu jede gewünschte Form entsprechend Ihrem Teiledesign erhalten. Materialien:Wissenschaftliche Instrumente Materialien:medizinisches Gerät

Micro injection molding Large series mass production is standard at starlim//sterner’s. Component weight goes down to 10 mg. Silicone components with a weight of below 10 mg are subjected to other physical laws. This is why starlim//sterner defines such products as "micro molding" parts. General definition of micro-injection molding The term comprises today 3 classes of components: Micro injection parts with micro structured areas (CD, "plastic-wafer", ... ) Micro injection parts or micro molded parts weighing a few milligrams (micro housings, watch hands, ...). Micro shaped components with tolerances and minimum dimensions in the µ range (gear wheels for watches, …). Range of starlim//sterner micro-injection molded parts Micro-silicone components below 10 mg with very precise undercuts and depressions Single and multi-component injection moldings Parts removal via Handling-Robot Optical monitoring of quality during processing Orientated parts depositing Optional: all activities are c

Saf polikarbonattan üretilmiş dayanıklı ve profesyonel çikolata kalıpları, makine ve elle üretime uygun kalıplar.

Als Service-Partner der Schüttgut verarbeitenden Industrie, entwickeln und realisieren wir mit Ihnen Ihr individuelles Projekt im Bereich Granulierung und Kompaktierung. Die Herstellung und Verarbeitung von Granulaten bietet eine Reihe von Vorteilen gegenüber dem Einsatz nicht-granulierter Feststoffe: So weisen Granulate eine verbesserte Fließ- und Haftfähigkeit auf, vorteilhaft beim Verpressen zu Tabletten. Die Gleichmäßigkeit der Granulate ermöglicht eine höhere Dosiergenauigkeit und die homogene Verteilung der Wirkstoffe. Da sich nicht alle Rohstoffe in trockenem Zustand optimal verarbeiten lassen, bieten wir unseren Kunden auch für diesen Fall die passende Lösung: Die Feuchtgranulation.

Mit leistungsfähigen Gießanlagen und einem eigenen Formenbau bieten wir Ihnen vom Einzelteil bis zur Serie ein hochflexibles Polyurethan-Sortiment an. Ein breites Halbzeug-Programm an PUR-Werkstoffen rundet den Service ab. Werkstoffe Vulkollan®, Polyurethan sowie PUR-Metallverbindungen. Formen, Dimensionen, Anwendungen Halbzeug in Form von: Sonderanfertigungen: Formteile: Platten 0,5 - 50 mm dick Blöcken Vierkantstäben Rundstäben 5 bis 230 mm ø geschliffenen Stäben von 5 bis 34 mm ø Rohren einschließlich Zuschneid-Service und mechanischer Fertigbearbeitung. Andere Dicken Überformate bis 4.000 x 2.000 mm bzw. bis 7.000 x 1.000 mm Armierte Platten mit Metalleinlage individuelle Härte-Einstellungen Sonderfarben Verschleißteile als Abstreifer z. B. an Schneeräumgeräten, Anschlagpuffer, Druckwalzen Membranen Mischerauskleidungen und PU-Beschichtungen von Siebanlagen Kupplungselemente Rakelstreifen PUR-Metallräder und -rollen und mehr

Spritzgießmaschinen (10.000 -16.000 kN) mit 1K-, 2K-, und 3K-Ausrüstung Wendeplatte, Indexplattenantrieb, maschinengeb. Drehteller und Schiebetisch

AOPB est autonome pour la fabrication des moules : - moules classiques, - moules 3 plaques, - moules à dévissage, - moules à canaux chauds, - moules de surmoulage d'inserts, - moules à versions.

* It is applied in 2 cm thickness. * 1 package of product is 20 kg. 1.6-1.8 kg of product is required for 1 m2 area. * You can easily reach an application area of ​​12 m2 by using a 20 kg Multiyap and a 6 mm notched trowel. * By providing waterproofing, even if the joint fillings between the tiles deteriorate, water does not leak to the lower floor. * There is no need to make water isolation in bathroom applications. * Since it is a hydrophobic product, a single product provides both water isolation and a strong tile ceramic application with superior performance. * It is quite light. It reduces labor and transportation costs. * It is flexible and the working time is extended. * It has strong adhesion feature.

REFERENCE : ARTP3200TCR25 ALPHA 3200 coloré PLATRE 3200 T.CUITE ROUGE 25kg -> Descritpion PLATRE DE MOULAGE COLORE POUR L'INDUSTRIE STATUAIRE -> Domaine d'application Produit teinté, spécialement conçu pour l'industrie statuaire : - Moulages durs, - Maquettes, - Statuettes, et ornement. -> Caractéristique Unité de vente : bidon de 25kg Minimum de vente : un bidon

For further data on the product, please refer to the data sheet or contact us. - Plastic blasting abrasives type WIWOX® KS have been specially developed for optimum, chemically neutral surface treatment and all gentle cleaning – especially for plastic and light metal. They are mainly used for paint stripping, roughening, matting, deburring and cleaning. Plastic blasting abrasives produce consistently high quality and do not cause any damage to the work piece to be treated.

Graisse synthétique pour charges lourdes - Au bisulfure de molybdène

Hartstoff gem. DIN 1100 Gruppe KS zur Herstellung von zementgebundenen Hartstoffestrichen gem. DIN 18560-7 und DIN EN 13813 sowie für die Herstellung von Industrieböden im Einstreuverfahren gem. DIN 18560-3. Hartstoffgruppe KS gem. DIN 1100:Schleifverschleiß ≤ 1,5 cm³/50 cm² gem. DIN EN 13813 Lieferform:30 kg Papierspezialverpackung

Plaques plastique injecté en 3 parties aimantées pour chocolats en 3D Dim. Moule = 275x175mm - Moules à 4 lignes de 7 diamants. Pour des diamants env. 10 à 12 gr avec garniture Référence:PDR9050 En stock:181 Produits Dimensions:Diam30x20mm 28pcs

Die Leistungspalette unserer mechanischen Fertigung ist auf die Herstellung von CNC Dreh-und Frästeilen für die Medizin- und Elektrotechnik sowie Maschinenbau und Halbleiterindustrie ausgerichtet. Vom Einzelteil bis zur Serie fertigen wir CNC-Drehteile, CNC-Frästeile, 3D-Druckteile in sämtlichen gängigen Werkstoffen. Gerne übernehmen wir auch die Montage für Sie. Made in: Germany

BİNBİR ÇEŞİT REKLER

Our company EMART GROUP, whose foundation year is 2020, continues to be the most preferred one in Turkey and the world in the export sector since its establishment, and at the same time, we are a manufacturer company that produces camera junction boxes, CCTV Accessories with quality materials. Our company, which provides service in the world and in Turkey, has consumers in more than 48 provinces in Turkey. Our company, which dominates the foreign market as well as the domestic market, has dealerships in many countries. These are Russia (Kazan and Krasnoyarsk), Palestine, Israel, Uzbekistan, Egypt, Algeria, Kazakhstan, Kenya, Iraq.

At TRADIUM, hafnium is available in the following forms for industrial supplies: - Hafnium metal: rods, pieces, sponge, ingots, round bars, wires, sheets, plates - Hafnium hydride powder - Hafnium oxide - Semifinished and finished products and manufacturing according to specifications Your point of contact for hafnium is: Frank Meier Phone: +49 (0)69 50 50 250 - 234 We are looking forward to hearing from you!

Ability solutions at home is just one section of the market that we service. This includes turning aids, standing aids and bed blocks. The purpose of these products is to make people's lives at home easier. They are very simple products but manufactured to a high standard to ensure they last a long time and perform to a high standard. All of these products are manufactured in the UK and hold the CE mark to show the standard to which they are tested.

LOGO

DESCRIPTION Façacryl est une peinture de dispersion acrylique de haute qualité spécialement conçue pour les façades. Très bonne adhérence sur toutes les surfaces minérales et diverses. Bon pouvoir couvrant, ne jaunit pas, respirant, parfaitement lavable et bon tendu. Rendement (indicatif) : 6-9 m²/L, selon le support Valeurs limites de l’UE pour ce produit (COV) : Cat. A/a : 30 g/L (2010). Ce produit contient moins de 30 g/L de produits COV.

Das Strahlen mit Kunststoff ist ein materialschonendes Strahlverfahren und wird angewendet zum entlacken und reinigen von dünnwandigen und empfindliche Blechteile bzw. Aluminiumbleche. D

Grout 2 HP Grout 2 HP is a pourable, fiber-reinforced mortar, used for structural restoration operations, anchoring of steel bars and strands, reinforced micropiles, tie rods, and riveting. The formulation contains very fine high-strength cements, micro-silicas with pozzolanic activity, aggregates in a rational granulometric curve (0.1 ÷ 1.8 mm), and special antisegregative additives. The product is mixed with 11% - 12% of water, requiring vigorous and prolonged mechanical mixing. The special formulation of Grout 2 HP provides the castings with mechanical strength, fracture energy, exceptional durability, and very high chemical-physical resistance. Grout 2 HP has a workability time of about 60-90 minutes, after which the setting process is triggered, followed by progressive hardening. The plastic and hygrometric shrinkage is extremely low thanks to the presence of Readymesh PM-060 multifilament synthetic fibers, which provide volumetric stability. The performances that make Grout 2 HP unique are: • very high compressive mechanical strengths (> 90 MPa at 28 days), • very high mechanical resistance to bending-traction (> 12 MPa after 28 days), • excellent durability and resistance to chemical attacks. Grout 2 HP is used for structural restoration operations, anchoring of steel bars and strands, reinforced micropiles, tie rods, and riveting. It is particularly suitable for operations where high mechanical performance is required after short curing (compressive strength at 3 days > 60 MPa) and in operations carried out in severe exposure environments (XC - XS - XF), characterized by aggression from sulphates, chlorides, and nitrates. The material can also be used for repairs in anchoring areas subject to high stresses. The application surfaces must be clean, free of dirt, crumbly and incoherent parts, dust, etc., and suitably saturated with water until reaching the condition of "saturated with dry surface". Adequate roughening of the surfaces by scarifying, sandblasting, etc. is always necessary to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). It is strongly recommended, for optimal performance of site operations, to use a vertical axis mixer with planetary movement or a double horizontal helicoid. The powder is mixed with drinking water to the extent of 11% - 12%, referring to the total weight of the mortar (about 2.75 liters per 25 kg bag) until a homogeneous mixture is obtained. Mixing time: about 4 minutes with a high efficiency mixer. The anchoring can be filled with a single screw pump, for mortars. Pumping must be carried out at a controlled speed to ensure a low working pressure. In case of restorations, the surface must be protected, after application, by polyethylene sheets or anti-evaporation treatments. Packaging: 25 kg bag Unit of Measure: €/kg

1- Su yalıtımı sağlayarak fayanslar arasındaki derz dolgular bozulsa bile alt kata su kaçırmaz, bina sakinlerini tamir masraflarından korur. Banyo uygulamalarında ayrıca su izolasyonu yapmaya gerek yoktur. Süper Hidrofobik bir ürün olduğu için tek bir ürün ile hem su izolasyonu sağlanmış olur hemde üstün performansa sahip güçlü bir fayans seramik uygulaması yapılmış olur. 2- Oldukça hafiftir. 3- 20 kg lık Multiyap Süper ile 6 mm taraklı mala kullanılarak 12 m2 lik uygulama alanına rahatlıkla ulaşabilirsiniz. 4- Hafifliği sayesinde inşaatlarda işçilik ve nakliye maliyetlerini düşürerek büyük oranda tasarruf sağlar. 5- Esnektir ve çalışma süresi uzatılmıştır. 6- Kuvvetli yapıştırma özelliğine sahiptir.