Termékek sika epoxy bevonat (22)

Syntech Poliurea Primer – Epoxy Metal Syntech Poliurea Primer – Epoxy Metal is a two-component primer based on epoxy resins free from solvents, used to promote adhesion, as a surface sealant for concrete, applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. Adhesion promoter, surface sealant for concrete, to be applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. The application must take place on a dry and degreased surface; the substrate must not have crumbly or detached parts and with a degree of humidity that must not exceed 5%. Preparation of the substrate may require some types of mechanical action: Smoothing, bush-hammering, shot peening, hydro-washing. Other mechanical actions that can make the support suitable. The individual components must be mixed carefully until a homogeneous mass is obtained. The material can be applied by roller, brush or spray by means of special airless machines, even in two coats. The temperature of the support must always be at least 3°C higher than the dew point temperature. Minimum application temperature +5°C, maximum temperature +35°C. Approximately 0,20 kg of Syntech Poliurea Primer – Epoxy Metal for every square metre of surface to be treated. Can 10 kg [A] - Can 5 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 5 kg [B]

Unsere moderne, umweltfreundliche und halbautomatische Pulverbeschichtungsanlage ist für Einzelteile und Kleinserien konzpiert. Sie ermöglicht die Beschichtung mit individuellen Farbtönen und Strukturen nach Kundenwunsch. Sie besteht aus einer Waschmaschine zur Entfettung und aus einer Pulverwand, zum Auftragen des Pulvers mit einer Handpistole. Zum anschließenden Einbrennen stehen 2 Öfen (Ofen1: L=3 m; B=1,2 m; H=1,7 m; Ofen 2: L=4,2m; B=1,8m; H=2,5m) zur Verfügung.

Biological based concrete stain and cement remover for resistant paving and flooring of natural and concrete stone. Fast and reliable removal of concrete-, cement-, lime- and efflorescence stains.

Das Epoxidharz-System E30RB ist eine 2K Epoxi-Rollbeschichtung mit mittlerer Verarbeitungszeit für hochwertige Boden- und Wandbeschichtungen ähnlich RAL7032 kieselgrau.

Nummer Eins chemicals 2008 Yılından beri Kimya sektöründe edinmiş olduğu tecrübeler ışığında müşterilerine en iyi ürünü ve hizmeti sunma felsefesi ile yola çıkarak İSTANBUL tuzla’da A.O.S.B de Epoksi ve Poliüretan Yapı Sistemleri, Antikorrozif epoksi ve poliüretan çelik konstrüksiyon ürünleri, Ahşap ve Metal tekneler için epoksi ve poliüretan ürünler, Su bazlı polimer esaslı su yalıtım sistemleri İç ve Dış mekanlarda kullanılan kaplama sistemlerine yönelik ürünlerin üretimine devam etmektedir. Firmamız kaliteli üretim kaliteli ürün anlayışı ile Avrupa normlarına uygun laboratuar cihazları ve analiz ekipmanlarına sahip ARGE ve Kalite Kontrol Laboratuvarında konusunda uzman mühendis ve kimyager kadrosu ile günümüz dünyasındaki teknolojik gelişimleri yakından takip ederek ürünlerini sürekli geliştirmekte ve yenilikçi bir anlayış ile çalışmalarını sürdürmektedir.

Eine industrielle Bodenbeschichtung, die dank ihrer Epoxidharz-Basis enorm chemikalienbeständig ist. In vielen Farben und den Versionen Säureresistent, Anti-Rutsch, Kalttrocknend, Rapid verfügbar.

ADLER PUR-based coatings are modern solvent-based systems that meet the most demanding standards in furniture and interior decoration. The best resistance, both for chemical and mechanical stresses and strains, as well as ease of application and use are the special features of this type of coating system. ADLER offers the best choice of PUR-based coatings for the most diverse types of wood as well as the most varied design concepts. Premium quality and efficient use are always ensured in the process. In this manner, you can meet almost any need or requirement for the surface as desired by your customers.

Beim Pulvern alle Farben möglich. Verwendung ausschließlich TGIC freier Pulver. Tribo- und Corona-Verfahren im Hand- oder Automatikbetrieb Auf Kundenwunsch auch 2 Schichten Pulver (Grundier- und Deckschicht)

Pardoseala epoxidica cu granule colorate Emex Quartz - See more at: http://www.e - Pardoseala Epoxidica Decorativa EMEX QUARTZ este un produs profesional, pe baza de rasini epoxidice fara solvent, disponibil intr-o gama infinita de modele obtinute prin inglobarea de granule de cuart sau marmura divers colorate in masa pardoselii. Acest tip de pardoseala se mai numeste si covor epoxidic. Produsul poate inlocui cu succes mozaicul sau gresia, avand in primul rand avantajul aspectului superior, dar fiind si o alternativa mult mai rezistenta atat la utilizare dar si in timp a acestora. Caracteristici principale: - Produs agrementat sanitar; - Aderenta excelenta la suport; - Etalare de exceptie; - Duritate excelenta; - Durabilitate mare; - Rezistenta mare la abraziune; - Rezistenta excelenta la uzura; - Rezistenta mare la agenti corozivi; - Rezistenta mare la hidrocarburi, medii acide sau alcaline.

Bei der Pulverbeschichtung wird ein elektrisch leitfähiges Material mit Pulverlack beschichtet.

fako® Dichtungskitt 3765 aus Butylkautschuk ist eine Ergänzung zum fako® Dichtband 3714. Ursprünglich entwickelt wurde für nahezu alle Dichtungszwecke, bei denen absolute Alterungsbeständigkeit erforderlich ist und eine Zwischenlage von 0,8 bis 1 mm verwendet werden muss. In Verbindung mit fako® Dichtband 3714 sind nahezu alle gewünschten Stärken bei Dichtungen zu erzielen. Er wird nicht hart, sondern bleibt plasto-elastisch. Dichtungskitt 3765 muss nicht nur elastisch, sondern auch plastisch sein, damit er beim Anpressen in jede Lücke dringen kann und darin verweilt, um so die Dichtung vollständig zu machen. Technisch ist dies nur erreichbar durch die Kombination zweier Grundstoffe mit gleichem chemischen Aufbau, aber verschiedenen Molekulargewichten. Durch diese zwei Komponenten wird die obige Forderung nach genügender Eindringtiefe bei gleichzeitiger Standfestigkeit des Kitts erfüllt. Durch einfaches Spachteln kann man eine Mindestdichtungsstärke von etwa 0,2 – 0,3 mm erreichen. Temperaturbeständigkeit:-50°C bis + 90°C im dauerhaft.Einsatz Haftfestigkeit:sehr gut erreichbare Mindestdichtungsstärke:von etwa 0,2 – 0,3 mm Eigenschaften:plasto-elastisch Ozonbeständigkeit:ozonbeständig

Suitable for professional Silicate Interior Wall Paint can be applied universally to viable lime- and cement plaster, concrete, brick and woodchip textured wallpaper. The solvent-free, silicate-enriched wall paint is specially made for these types of surfaces. Its special composition creates an inseparable microporous bond with the substrate. This silicification results in perfect adhesion and produces extremely strong durability even on critical substrates. Highest color stability: A1 (FB-Code, BFS-MB Nr. 26).

Die IPA Polyschicht ist eine kuststoffmodifizierte Silikatbeschichtung mit höchster chemischer Beständigkeit und DIBT- Zulassung. Abscheider, Domschächte, Faultürme, LAU - Anlagen, Tankwannen, Waschstraßen etc. werden mit der IPA Polyschicht dauerhaft saniert.

One Side Adhesive for LEATHER'S PRODUCERS The NEOPRENE ONE WAY is a plychloroprene adhesive adapt for LEATHER'S PRODUCERS and GIUNETRIA in particular in the case where you want apply the glue only in a side. Used for the construction of insoles in shoes too. It has high viscosity. High bond strength. CHARACTERISTICS : Viscosity : 2800 +/- 100 cPs Opened Time : 30 - 60 Minutes USING INSTRUCTIONS : Apply an homogeneous coat upon one of the two parts has to be sticked, let it dries for at least 10 - 15 minutes and join the two parts with hands, hammer or with a press. To dilute the PRODUCT, use SOLVENT P or SOLVENT M. The products has to be conserved in the original tins well closed and in a cool and dry place. N.B.: All the indications over reported are without obligation and warranty. PACKAGING : Kg 800 - Kg 200 - Kg 40 - Kg 15 - Kg 9 Kg 4 - Kg 1 .

Multi-purpose, high-quality, single-component foam with excellent properties, capable of hardening with ambient air humidity Features - Highly expandable - Paintable finish - Availability of application at low temperatures - Easy application and high efficiency - Resistance to mould and humidity Fields of Application Assembling and insulating door and window frames; insulating pipelines and filling pipeline joints; insulating energy lines; fastening and insulating wall boxes, switchboards and roof panels; filling fractures and cracks Method of Application Ensure that surfaces of application are dry and cleared from dust and grease. Thoroughly shake the tube for at least 30 seconds before use. Open the protective cap and attach the plastic trigger to the valve. Handle the box so that the valve is always positioned below. By using the valve lever, check the amount of foam released. Moisten each layer. Avoid smoking during the application.

Référence GCNOIRPIS-25KG

EG 91 Epoxy-polyurethane two-component elastoplastic and thixotropic sealant, for joints subject to traffic, where Shore A Hardness Scale = 65. The elongation-at-break is 70%. To be applied with a trowel or extruded into the suitably-taped sections of the joint (to protect adjacent surfaces). Resistant to contact with hydrocarbons (gasoline and diesel fuel). Horizontal sealing of joints in industrial flooring, even in the presence of chemical attacks and stresses from average-heavy traffic. Vertical sealing of joints in concrete works and products. The application and containment surfaces (joint walls) should be clean, dry, conveniently prepared and adequately resistant: free from dust, grease, soiling, crumbling and/or non-adhering parts and dry. The application surfaces must also be preliminarily treated with Protech Flex Primer. Add component B to component A taking care to pick up all the material contained in the packs, mix thoroughly with a mixer at a low number of revolutions, until a perfectly homogeneous mix is obtained; add the required load amount (component C) continue to mix until a perfectly homogeneous mixture is obtained, indicated by the uniform colour of the mixture. Apply the product mixed by trowelling or with extrusion guns. Do not apply with temperatures below + 5°C or higher than + 35°C and in the presence of surface stagnant water. Approximately 1.25 kg of EG 91 per cubic decimetre of joint volume to be sealed (1250 kg per cubic metre). Packaging: Kit of 5+2.5 kg UM: €/kg

Syntech Poliurea Top Coating A protective, pigmented, two-component formulation based on aliphatic polyurethane resins, ideal as a protective and aesthetic coating on waterproofing with SYNTECH POLIUREA SPRAY. Characterised by high levels of elasticity and elevated protection, even in aggressive atmospheres. Available on request in shades from the RAL colour range. Surface coating pigmented for colouring polyurethane claddings, and their protection from UV rays (which in the absence of the top coating would alter the colour over time). After suitable priming with SYNTECH POLYUREA PRIMER, it can also be applied as a simple coloured aliphatic protective coating. Polyurea support Vacuum and blow the surfaces to eliminate any dust that may have accumulated in the 24-48 hours following the installation of SYNTECH POLIUREA SPRAY Support in concrete, mortar, brick, tiles The support on which the polyurea system must be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. It is recommended to use Primer from the SYNTECH POLIUREA PRIMER range. On particularly absorbent substrates, to avoid the formation of craters / blowholes on the surface of the freshly sprayed product, it is recommended to use primers from the SYNTECH POLIUREA PRIMER range, always contacting the Azichem technical staff for clarification on the most suitable type to use. Apply several layers of primer until the porosity is saturated and providing a light dusting with clean and dry quartz sand (0.4-0.7 mm). Never dust off the primer. Provide suitable elastic sealing systems to cover joints, fittings, cracks or fissures subject to significant movements. Pour component B with component A into a single container, taking care to remove all the material from the packaging. Mix thoroughly with a mixer at low revs, until a lump-free mixture is obtained. Apply with a roller or brush on the surfaces of SYNTECH POLYUREA SPRAY, within 24-48 hours of spreading the latter. A thorough sanding of the supports is recommended for any repairs and/or finishes. From 0.15 to 0.25 kg of SYNTYECH POLIUREA TOP COATING for each square metre of surface to be covered. Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]

Syntech HAG Acryl Syntech HAG Acryl is a four-component resin that reacts to form an elastic and durable gel. The properties of Syntech HAG Acryl are: • Good general chemical resistance. • Does not contain acrylamide, methacrylamide, formaldehyde or solvents. • Not inflammable. • Excellent adhesion on mineral building materials such as concrete, cement and bricks. • The reaction speed can be adjusted from a few seconds to several minutes. • When the injected cracks dry out due to temperature or groundwater level fluctuations the gel does not crack easily. • The hardened gel has excellent durability in wet-dry cycles. Syntech HAG Acryl components are supplied ready to use. Create 2 mixes in separate plastic buckets. Prepare only the quantity to be used each time. Solution 1: Syntech HAG Acryl component A (25 kg resin) mixed with Syntech HAG Acryl component B (2.5 kg catalyst). Solution 2: Syntech HAG Acryl component C (2 packs of 0.625 kg) mixed with clean tap water. Attention: The amount of water must be equal in volume to solution 1. When mixing resin, always use a wooden or stainless steel spatula. The reaction time depends on the temperature of the material, the structure of the building and the possible amount of water present. Higher temperature will speed up the reaction time and lower temperature will slow it down. It is advisable to carry out an on-site test, before injection, to observe and define the reaction time. To change the reaction time, only adjust the amount of Syntech HAG Acryl component C. The amount of the other components remains the same. Use a two-component stainless steel pump (manual, electric or pneumatic). Check that the pump and equipment are clean and that there is no residue from previous injection work. The two mixtures are fed into the pump separately, but are mixed homogeneously at a volumetric ratio of 1:1 in the pump's mixing head, before being injected through the pump nozzle. Check the quality of the concrete, as injection involves pressure. Sealing and waterproofing of cracks and cavities in walls, floors, concrete constructions, underground structures, etc. It can be used in constructions that are not permanently in contact with water (fluctuating groundwater level). Injection of very fine cracks. Determine the type and size of packers based on your pump and injection type. If reinforcing steel is present, try to locate it and plan the drilling pattern so that the reinforcement is not drilled. Drill holes at an angle of approximately 45° or less and in the direction of the crack. Make sure the hole goes through the crack. The distance of the drilled holes depends on the width of the crack. Place the packer in the hole. Prepare the pump to start the injection. The injection pressure varies depending on the structure and size of the crack. Start the injection at the lowest point of the crack. Continue injecting until resin flows out of adjacent packer(s). This is necessary to achieve uniform distribution of the material. Stop pumping, unplug and move on to the next packer. Continue the procedure until the crack is completely filled. After the material has cured, the packers can be removed. Holes drilled can be covered with Repar Tix Speedy HP quick-setting mortar. Clean and rinse the pump equipment with water whenever there is a stoppage longer than 15 minutes and, after completing the injection, rinse with a sufficient amount of water. Make sure the pump is clean and stop only when clean water comes out of the pump. The consumption of the product depends on the size of the empty volume to be filled. Can 25 kg [A] - Plastic can 2.5 kg [B] - Canister 0.625 kg [C] - Canister 0.625 kg [D] - Kit: 1 Can 25 kg [A] + 1 Plastic can 2.5 kg [B] + 1 Canister 0.625 kg [C] + 1 Canister 0.625 kg [D]

Wasserbasiertes, mattes, vergilbungsfreies 2K-Lacksystem für die einschichtige Verarbeitung. Das Produkt zeichnet sich durch exzellente Witterungs- und UV-Beständigkeit, sehr gute Kratzfestigkeit, hohe Blockfestigkeit sowie Chemikalienbeständigkeit aus. Polycolor 2K SQ W10 Weiß, tönbar Besondere Eigenschaften Eignungsnachweis nach DIN EN 927-2 Freibewitterung Prüfung der Wetterechtheit nach RAL-GZ 716, Teil 5 sowie DIN EN 513: 1999-10, Verfahren 1 (SKZ) Prüfung der Erwärmung nach RAL-GZ 716, Teil II-a-3, Anhang I (SKZ) Französische Verordnung DEVL1104875A über die Kennzeichnung von Baubeschichtungsprodukten auf ihre Emissionen von flüchtigen Schadstoffen: A+ Auftragsart Airless Airless luftunterstützt (Airmix, Aircoat, etc.) Druckbecherpistole

Walzgrund für Holz auf Basis UV-vernetzbarer Polyacrylatharze; verleiht UV-AC-Walzlackaufbauten eine ausgezeichnete Haftung zum Untergrund bei starker mechanischer Belastung. Innolux Primer Auftragsart Walzen

Référence GCMOULEPIN-25KG