Termékek acélunk (230)

SPIROL's Series 101 Headrest Coiled Spring Pins were designed specifically for use in automotive headrest assemblies. The advantages of SPIROL's headrest pins are as follows: • Absorbs shock and vibration • Increased productivity • 100% dimensional control • Symmetrical • Non-interlocking • Accommodates wide hole tolerances • Easy to install • Simplified logistics • Global supply

The electronic pressure switch DS 201P is the successful combination of — intelligent pressure switch — digital display and is designed for universal applications in the mechanical engineering and other industries where a flush stainless steel diaphragm is necessary. This can be the case, for example, with higher viscous or slightly contaminated fluids. For usage with higher media temperature optionally a cooling element up to 300 °C is available. Features: — nominal pressure: 0 ... 60 bar up to 0 ... 400 bar — accuracy: 0.5 % FSO — 1, 2 or 4 independent PNP contacts, freely configurable — rotatable and configurable display module — indication of measured values on a 4-digit LED display Optional Features: — IS-version Ex ia = intrinsically safe for gases — cooling element up to 300 ° C — customer specific versions

Vanne à brides avec corps en acier inoxydable pour les fluides neutres et corrosifs. Longueur et modèle de bride conforme à DIN et ANSI. Versions Version basse température Version à décharge de pression Version sans huile, graisse silicone ou PTFE ... Taille::DN 15 - DN 150 Pression::PN 16; PN 40, ANSI#150 Matériau::Acier inox 1.4408; 1.4308 Température::-100 °C - 220°C Raccords::Brides conformes à la norme DIN EN 1092-1; Longueur conforme à la norme DIN EN 558-1 série 1 Accessoires::Interrupteur de fin de course; Electro-vanne de pilotage; Commande manuelle en cas d'urgence Autres modèles de commande::Actionneur à piston en : Laiton (chromé), Inox, Plastique; Actionneur à diaphragme en acier inox Application::Gaz, vapeurs, liquides

SPIROL Standard Slotted Spring Pins SPIROL Standard Slotted Spring Pins have a slot width narrower than the wall thickness and thus do not nest or interlock. This feature, combined with a smaller expanded (pre-insertion) diameter, results in a number of advantages for SPIROL Standard Slotted Pins compared to ISO 8752 pins including: • Lower insertion force and smoother insertion. • Rounder pins, which in turn results in better conformance of the pin to the hole wall and eliminates the edge of the slot damaging the hole during insertion. • Lower stress in the spine of the installed pin. This results in longer pin life in shock or fatigue applications. • Ability to use automatic vibratory feeding of pins for installation without interlocking. • Plating of pins for additional corrosion resistance or appearance without “touch marks” or the bonding of nested pins. Please visit www.SPIROL.com to learn more!

Der elektronische Druckschalter DS 201P ist die gelungene Kombination aus — intelligentem Druckschalter — digitalem Anzeigegerät und ist für Anwendungen im allgemeinen Maschinenbau sowie in anderen Bereichen vorgesehen, wo eine frontbündige Edelstahlmembrane gefordert ist. Dies kann insbesondere bei höherviskosen oder leicht verschmutzten Medien der Fall sein. Für höhere Medientemperaturen ist optional ein Temperaturentkoppler bis 300 °C lieferbar. Merkmale: — Nenndrücke: 0 ... 60 bar bis 0 ... 400 bar — Genauigkeit: 0,5 % FSO — 1, 2 oder 4 unabhängige PNP-Ausgänge, frei konfigurierbar — Anzeigemodul dreh-und konfigurierbar — Messwertanzeige auf 4-stelligem LED-Display Optionale Merkmale: — Ex-Ausführung Ex ia = eigensicher für Gase — Temperaturentkoppler bis 300 ° C — kundenspezifische Ausführungen

The differential pressure transmitter DPT 200 has been especially designed for the process industry and can be used for level measurement of closed, pressurized tanks, pump or filter controlling, etc. The possibility passes different pressure seals at the DPT 200 adding with different membrane materials to reach an optimal adaptation to the application. Features: — differential pressure von 1 mbar bis 20 bar — static pressure bis max. 400 bar — turn-down max. 100:1 — accuracy: 0.075 % FSO — HART®-communication — output signal: linear or square root extraction — aluminium housing Optional Features: — IS-version: Ex ia = intrinsically safe Version (group II) EX ia= intrinsically safe Version for firedamp mines (group I) Ex d = flameproof enclosure (group II) — LC-Display — stainless steeel housing

Pneumatisch betätigtes Dreiwege-Stellventil mit einem integrierten Stellungsregler für anspruchsvolle Regelaufgaben. Durch die Edelstahlausführung für neutrale und aggressive Medien geeignet. Stellungsregler: Digitaler Stellungsregler Typ 8049Pneumatischer und elektropneumatischer Stellungsregler Typ 8047Stellungsregler mit integriertem Prozessregler Typ 8049 IPCStellungsregler Typ 8047 und Typ 8049 auch in explosionsgeschützter Ausführung Antriebsvarianten: Kolbenantrieb aus- Messing (verchromt)- Edelstahl- KunststoffEdelstahl-Membranantrieb Ausführungen: Unterschiedliche Steuerfunktion z. B.: Aufteil- und Mischfunktion; TieftemperaturausführungÖl-, Fett-, Silikon- oder PTFE-freie Ausführungen… Nennweite:DN 15 - DN 50 Nenndruck:PN 40 Werkstoffe:Edelstahl 1.4408 Temperatur:-100°C bis +220°C Anschlüsse:"Whitworth-Rohrgewinde; NPT-Gewinde" Zubehör:Induktive Endlagenschalter Anwendung:Gase, Dämpfe, Flüssigkeiten

SPIROL propose une gamme de rondelles ressort en acier inoxydable austénitique dans des diamètres allant de Ø8 mm à Ø71 mm. L'acier inoxydable austénitique est généralement utilisé pour les applications statiques et à faible cycle qui nécessitent un niveau élevé de résistance à la corrosion. Il résiste très bien à l'eau douce et aux conditions atmosphériques marines, et convient à de nombreuses autres conditions industrielles, y compris les environnements acides. Ce matériau continue à se durcir à l'usage, la durée de vie est donc limitée, mais la résistance au fluage est bonne. SPIROL fournit des rondelles ressort individuels ainsi que des rondelles ressort pré-empilés dans des configurations personnalisées, emballés dans un film rétractable avec une languette perforée pour faciliter l'assemblage.

SPIROL's FH400 Headed Barbed Pin has a series of barbs extending down the entire length of the pin. Headed Barbed Pins are a great replacement for self-tapping screws in plastic assemblies as Barbed Pins are installed into standard moulded (or drilled) holes, they install much faster than screws, and they eliminate issues associated with cross-threaded or skewing during installation. Unlike screws that resist back-out (or loosening) by being tightened to a preset torque, Barbed Pins are retained by the plastic backfilling over the aggressively-designed barbs. The head provides a positive stop and is also used to retain a thin component to a thicker component within an assembly. SPIROL's FH400 Headed Barbed Pins are available in metric diameters ranging from Ø2mm to Ø6mm and inch diameters ranging from Ø.078" (5/64) to Ø.250" (1/4) in low carbon steel and austenitic stainless steel.

SPIROL invented the Coiled Spring Pin in 1948. Truly an engineered fasteners, the Coiled Pin is available in three duties, light, standard and heavy, to enable the designer to choose from the optimum combination of strength, flexibility and diameter to suit different host materials and application requirements. Their shock absorbing design dampens forces and vibration to prevent hole damage and prolong assembly life. Light Duty Coiled Spring Pins are generally recommended for soft, brittle or thin materials such as plastics, aluminium, die castings, ceramics, and where holes are located close to an edge of the assembly. In situations not subjected to significant loads, such as when used purely for alignment or as an axle, light duty Coiled Pins are often used because of easy installation resulting from lower insertion force.

Vanne d’équerre pneumatique pour des capacités de commutation élevées et des installations compactes. Exécution en acier inoxydable convient également pour utilisation avec des fluides neutres et agressifs et dans une large gamme de températures. Versions Version basse température Version sans huile, graisse silicone ou PTFE Taille::DN 15 - DN 50 Pression::PN 40 Matériau::Acier inox 1.4408 Température::-30 °C - 200°C Raccords::Taraudage whitworth; Taraudage NPT Accessoires::Interrupteur de fin de course; Electro-vanne de pilotage; Commande manuelle en cas d'urgence Autres modèles de commande::Actionneur à piston en : Laiton (chromé), Inox, Plastique; Actionneur à diaphragme en acier inox Application::Gaz, vapeurs, liquides

SPIROL's FH300 Headed Helical Knurled Pin has the same body style as the KP300 Helical Knurled Pin, with the addition of a head. A Headed Pin is typically used to provide a positive stop or to retain a thin component to a thicker component within an assembly. FH300 Headed Helical Knurled Pins have a flat head, however they are available to order with a round head (RH300) to meet specific application requirements. Similar to the SPIROL Series KP300 Helical Knurled Pin offering, SPIROL's FH300 Headed Helical Knurled Pins are available in metric diameters ranging from Ø2mm to Ø6mm and inch diameters ranging from Ø.078" (5/64) to Ø.250" (1/4) in low carbon steel and austenitic stainless steel.

SPIROL offers Spacers specifically designed for use in conveyor systems and garage door hinge assemblies. Both SPIROL's Conveyor Spacers and Garage Door Spacers are manufactured from galvanised steel to provide the necessary strength and corrosion protection at a fraction of the cost of plated cutoff tubing and machined bushings. SPIROL stocks the raw material and tooling required to manufacture the standard sizes of Conveyor Spacers and Garage Door Spacers. Intermediate lengths can be produced without additional tooling.

Starke Leistung Je nach Bedarf erzeugen die Hydraulikaggregate unserer Brikettiersysteme einen spezifischen Pressdruck von bis zu 5000 kg/cm². Hohe Effizienz Die Anlage presst aus feuchten Metallspänen anhaftende Kühlschmierstoffe heraus, welche nach einem Aufbereitungsprozess wiederverwendet werden können. So reduziert sich der Verbrauch der teuren Schmiermittel deutlich und wirkt der oftmals kostspieligen Entsorgung von nassen Spänen oder Schlämmen entgegen. Im Vergleich zu losen Spänen ist beim Einschmelzen von Briketts der Verlust durch Abbrand deutlich geringer und die Schmelzausbeute somit höher. Optimale Anpassung Im Metallbereich können Sie zwischen Brikettformaten von 60x40mm und bis zu 150x120mm auswählen. Die Brikettlänge ist dabei in gewissen Grenzen variabel. Die Auswahl des Brikettformats ist abhängig von der benötigten Durchsatzleistung sowie Art bzw. Form des Ausgangsmaterials und dessen Schüttdichte. Durchsatzleistung: bis zu 5000 kg/h Material:Metall Max. Durchsatzleistung (kg/h) - Aluminium:30 - 2000 kg/h Max. Durchsatzleistung (kg/h) - Stahl & Guss:30 - 3000 kg/h Max. Durchsatzleistung (kg/h) - Messing, Bronze, Kupfer:50 - 5000 kg/h Motorleistung (kW):4 - 90 kW Spez. Pressdruck, max . (kg/cm²):1400 - 5000 kg/cm² Brikettformate:60x40, 60x60, 80x40, Ø60, Ø80, Ø70, Ø 100, Ø 120, Ø 150, 150x60, 150x75, 150x120150x120 Gewicht (t):1 - 12 t

SPIROL fabrica Pasadores Elásticos en Espiral de acero inoxidable 316 para satisfacer los requerimientos de aplicaciones específicas. El acero inoxidable tipo 316 es similar al acero inoxidable tipo 302/304 con un poco mayor contenido de níquel y la adición de molibdeno. El contenido de molibdeno aumenta en gran manera la resistencia química de esta aleación. El 316 muestra una mayor resistencia contra las picaduras debido al agua de mar, ácido acético, salmueras de cloruro, sodio y calcio, soluciones de hipoclorito, ácido fosfórico y los licores de sulfito y ácidos sulfurosos utilizados en la industria del papel y la pulpa. Esta aleación también es austenítica, no magnética y no endurecible mediante métodos convencionales. El acero inoxidable 316 tiene mejores propiedades mecánicas a temperaturas elevadas que el 302/304 y ofrece una excelente integridad mecánica a temperaturas bajo cero. Las aplicaciones típicas de los Pasadores en Espiral de acero inoxidable 316 de SPIROL incluyen la

SPIROL's Series 880 Coiled Spring Pin was designed specifically for use as the hinge pin for PC board card lock and ejector clip mechanisms. The quality of the hinge is unsurpassed by other fastening methods due to the low insertion force and compression of the pin during and after installation. As with all Coiled Spring Pins, the Series 880 hinge pin for PC board card locks and ejector clips is self-retaining, and thus no secondary processes are required for retention. The Coiled Pin's uniform radial spring force results in a controlled hinge movement that remains consistent throughout the life of the assembly.

Schleifschlämme entstehen beim Schleifen metallischer Bauteile. Sie sind ein Gemisch aus Metall- und Korundabrieb in Kombination mit dem eingesetzten Kühlschmierstoff (KSS). Die Brikettierlösung von RUF ermöglicht es, Schleifschlämme kostengünstiger zu entsorgen bzw. zu recyceln. Durch das Brikettieren sinkt die zu entsorgende Menge deutlich und die Briketts verfügen über eine definierte Restfeuchte. So werden die Entsorgungskosten gesenkt und je nach Legierung besteht sogar die Möglichkeit, die Briketts gewinnbringend zu verkaufen. In den meisten Fällen kann das in den KSS enthaltene teure Öl wieder eingesetzt werden. Dies führt zu signifikanten Einsparungen. Bereits bei ca. 10 bis 30 Tonnen ölhaltigem Schleifschlamm pro Jahr kann sich die Brikettieranlage in weniger als 12 Monaten amortisieren. Max. erreichbarer spezifischen Pressdruck: bis zu 3.800 kg/cm2. Die Durchsatzleistungen von RUF Brikettiersystemen speziell für Schleifschlamm liegen zwischen 40 und 350 kg/Std. Material:Schleifschlamm Max. Durchsatzleistung (kg/Std.):40 - 350 kg/Std. Motorleistung (kW):4 - 22 kW Spezifischer Pressdruck (kg/cm²):2000 - 3800 kg/cm² Brikettformate:60x40, Ø60, Ø80, Ø100, Ø120 Gewicht (to):1 - 3,7 to

Der Industriedruckmessumformer DMP 335 basiert auf einem verschweißten Drucksensor aus Edelstahl, welcher keine Druckübertragungsflüssigkeit besitzt. Diese Eigenschaft ist von besonderem Nutzen bei Applikationen bei denen Silikonöl oder Elastomerdichtungen nicht verwendet werden können. Merkmale: — Nenndrücke: 0 ... 16 bar bis 0 ... 600 bar — Genauigkeit: 0,5 % FSO — geeignet für Sauerstoffapplikationen — unempfindlich gegen Druckspitzen — hoch überlastfähig Optionale Merkmale: — Ex-Ausführung Ex ia = eigensicher für Gase und Stäube — kundenspezifische Ausführungen

Der Differenz-Drucktransmitter DPT 200 wurde speziell für die Prozessindustrie konzipiert. Typische Einsatzbereiche sind z.B. die Füllstandsmessung von geschlossenen, druckbeaufschlagten Behältern, Überwachung von Pumpen- oder Filteranlagen, u.v.m. Beim DPT 200 besteht die Möglichkeit verschiedene Druckmittler mit unterschiedlichen Membranmaterialien anzubauen, um eine optimale Anpassung an die Applikation zu erreichen. Merkmale: — Differenzdruck von 1 mbar bis 20 bar — statischer Druck bis max. 400 bar — Turn-Down max. 100:1 — Genauigkeit: 0,075 % FSO — HART®-Kommunikation — Ausgangssignal: linear oder radiziert — Aluminiumgehäuse Optionale Merkmale: — Ex-Ausführungen: Ex ia = eigensichere Ausführung (Gruppe II) Ex ia=eigensichere Ausführung für schlagwettergefährdete Bergwerke (Gruppe I) Ex d = druckfeste Kapselung (Gruppe II) — LC-Display — Edelstahl-Gehäuse Material:Edelstahl

SPIROL is a technical resource that provides high quality components that improve the quality of your assembly, extend the life of your products and reduce your manufacturing costs. We are the leading global manufacturer of engineered fasteners, shims, installation machines, and parts feeding equipment producing over two billion components annually. In addition to high quality products, SPIROL has Application Engineers throughout the world to assist you in your designs, supported by state-of-the-art manufacturing centers and global stocking facilities to simplify the logistics of delivering your product. If you have any questions or would like complimentary Application Engineering support, please feel free to contact us at any time!

The stainless steel probe DCL 531 with RS485 interface uses the communication protocol Modbus RTU which has found the way in industrial communication as an open protocol. The Modbus protocol is based on a master Slave architecture with which up to 247 Slaves can be questioned by a master – the data are transferred in binary form. Basic element is a high quality stainless steel sensor with high requirements for exact measurement with excellent long term stability. Features — nominal pressure: 0 ... 1 mH2O up to 0 ... 250 mH2O — accuracy: 0.25 % FSO — output signal: RS485 with Modbus RTU protocol — diameter diameter 26.5 mm — small thermal effect small thermal effect — high accuracy excellent accuracy — reset function Optional Features — drinking water certificate according to DVGW and KTW — different kinds of cables — different kinds of seal materials Housing material:stainless steel Signal output:Digital - Modbus RTU/RS485 measuring cell:stainless steel

SPIROL offers robust, vertical installation machines specifically designed to post-mould install Compression Limiters into a variety of plastic assemblies. The machines can install a single Compression Limiter or multiple Compression Limiters simultaneously into various polymers, thermoplastics and thermosets. SPIROL’s Compression Limiter Installation Machines are versatile solutions designed to be retooled to accommodate changing part configurations. All designs incorporate standardized machine components to reduce factory lead time, improve component reliability, and lower component costs. SPIROL also specializes in application-specific fixtures to ensure that all assembly components are held accurately in place through the installation process.

The SPIROL Model PH Heat Insert Driver provides an accurate and consistent method to simultaneously install multiple Threaded Inserts or Compression Limiters at multiple elevations. Simultaneous installation dramatically increases productivity and simplifies the number of manufacturing steps to complete an assembly. Additionally, the platen head and fixture can be easily changed to accommodate quick change-over to different assemblies associated with new production runs. This machine can be used to install 12 Inserts into 1 assembly, or a fewer number of Inserts into a larger number of assemblies – as long as the total combination does not exceed 12 Inserts.

Wrapped composite sliding bearing steel / Special PTFE coated Maintenance-free dry sliding bearing | DIN 1494 / ISO 3547 TEF-MET/P is a versatile dry sliding bearing with PTFE sliding layer. Therefore, no lubrication is necessary. However, it is very well suited for lubricated applications (e.g. hydraulic oil lubrication). For technical details, please visit the product page on our website! Support material/Carrier material:Steel tin-plated Intermediate layer:Sintered bronze Sliding layer:PTFE + fillers Static load:≤ 250 [N/mm2] Dynamic load:≤ 140 [N/mm2] at slow sliding speed Sliding speed:≤ 2,5 m/s Friction value:0,02 to 0,18 Temperature strain:– 200 to + 280 °C Max. PV-value:1,8 N/mm² x m/s Housing Ø:H7 Bushing inner-Ø after mounting:H9 Shaft tolerance:f7

SPIROL's Knurled Pins are manufactured with two different knurl types: straight knurls and helical knurls. Unlike a Straight Pin, where retention is provided by the uniform interference between the pin and hole, Knurled Pins are designed to cut into the host. The displacement of the host material into the valleys of the knurls yields more frictional contact area between the Knurled Pin and hole; thus resulting in higher retention. Solid Pins with retention features such as knurls and barbs allow for wider hole tolerances than Solid Pins without retention features (i.e. Straight Pins).

Wrapped spring steel plain bearing | Requires maintenance | DIN 1498 | DIN 1499 FER-MET® is a spring steel plain bearing without integrated sliding material. Lubrication of the bearing point is necessary. Very high load capacity and impact resistance for heavy-loaded applications with impact loads. Very wear-resistant. A standard gap design with a straight slot and without chamfer inside [EG], but can also be manufactured with other slot shapes if required. For technical details, please visit the product page on our website! Support material/Carrier material:55Si7/CK67 Static load:≤ 350 N/mm² Dynamic load:≤ 200 N/mm² Sliding speed:≤ 1,1 m/s Friction value:0,50 up to 0,60 µ Temperature strain:-200 up to +350 °C Max. PV-value:1,2 N/mm² x m/s Hardness:48 – 52 HRC Housing Ø:H8 Bushing inner-Ø after mounting:D10 up to D13 Shaft tolerance:f7 up to h8

Die Edelstahl-Tauchsonde DCL 531 mit RS485-Schnittstelle benutzt das Kommunikationsprotokoll Modbus RTU, welches als offenes Protokoll Einzug in die industrielle Kommunikation gefunden hat. Das Modbus-Protokoll basiert auf einer Master-Slave-Architektur, bei der bis zu 247 Slaves von einem Master abgefragt werden können – die Daten werden in binärer Form übertragen. Basiselement ist eine hochwertige Edelstahlmesszelle, die besonders für genaue Messungen mit guter Langzeitstabilität geeignet ist. Merkmale — Nenndrücke: 0 ... 1 mH2O bis 0 ... 250 mH2O — Genauigkeit: 0,25 % FSO -Ausgangssignal: RS485 mit Modbus RTU Protokoll — Durchmesser 26,5 mm — geringer Temperaturfehler — hohe Genauigkeit — gute Langzeitstabilität — Resetfunktion Optionale Merkmale — Trinkwasserzulassung nach DVGW und KTW — verschiedene Kabel- und Dichtungsmaterialien Gehäusematerial:Edelstahl Signalausgang:Digital - Modbus RTU/RS485 Messzelle:Edelstahl

The battery-powered BAROLI 02 enables a local displaying of values, satisfying the highest demands for accuracy and long-term stability. The pressure gauge may be applied compatible with the stainless steel used; it shows an excellent robustness and a high overpressure protection. The BAROLI 02 display housing is rotatable, thus ensuring an easy reading even under unfavorable mounting conditions. Additional functions: changing the unit, displaying min / max values, calibrating of offset and the span, configuring the automatic switching-off. Features: — nominal pressure: 0 ... 100 mbar up to 0 ... 600 bar — accuracy: 0.125 % FSO — stainless steel diaphragm — 2-line LC display, 4.5-digit 7-segment display, 6-digit 14-segment additional Display — mechanical connections: inch, NPT threads Optional Features: — min- / max-function with reset function — offset and end point calibration — setting the pressure unit

The SPIROL Model HA Automatic Heat Insert Driver provides an accurate and consistent method to install virtually any type of Heat/Ultrasonic Style Insert into thermoplastic assemblies. With this exceptionally versatile machine, the operator does not need to physically touch the Insert during the entire installation process. SPIROL’s Model HA Automatic Heat Insert Driver has been designed to eliminate the dependency on the operator to control the factors of time, temperature and pressure to ensure nearly perfect flow of the plastic for optimal retention and performance. The Model HA Automatic Heat Insert Driver installs Threaded Inserts ranging in size from M2 – M8 metric threads and #2 – 3/8 unified threads. The machine can be configured to accommodate a variety of applications and the heat tips are easily interchangeable to accommodate various sized Inserts.

The Model CLX operates the same way as SPIROL's Model CL, yet this extra-large Compression Limiter Installation Machine is custom-designed to accommodate larger assemblies outside the standard footprint of the Model CL. Visit www.SPIROL.com to learn more!