Termékek acélunk (2042)

Milled toothing, straight teeth engagement angle 20°, bright. Outside diameter extruded, tolerance h9. Note The gear rack teeth are cut using a hob mill. This results in minus tolerances for dimensions H and H1 up to module 2 0.2 mm. module 2.5 to 3 0.3 mm. Reference:22425-20 Material:Stainless steel 1.4305

Rondelles Carrées pour Constructions Bois (r carrées/bois) Inox A2 - DIN 436 Modelo:62540

D = variable gap according to processe DN = nominal diameter

d = inner diameter of the groove d1 = shaft diameter

Cette réduction en inox 316L usinée permet de réduire un filetage et d'adapter le raccordement dans un réseau fluide. Elle est proposée pour des filetages allant de 1/8" à 3". Diamètres disponibles : :du DN8-6 au DN80-65 Filetage ::Gaz ou NPT Pression nominale de la réduction à 20°C ::20 bar Pression nominale de la réduction à 100°C ::16 bar Norme ::ISO 7-1 (sauf NPT)

Ecrous Relieurs Fraisés Bombés Fendus (ECR RELIEURS TFBF) Inox A2 Modelo:62630

Ecrous Hexagonaux Indesserables Lubridiés Avec Bague Nylon (ECR HI Index lubrifiés) Inox A2 - DIN 985 Existe une variante en Inox A

Stainless steel 1.4305 Lamellar insert polyamide (PA6). Seal ring CR / NBR. O-ring NBR. Version: Bright. Note: DIN EN 60423 cable glands with metric thread. Sealing and tension relief are provided by inset fins and a sealing washer. Rating IP68 (5 bar for 30 min). Cable glands are used for connecting fixed calbes and lines in housings, distributors and switch boxes. Temperature range: Static: -40 °C to +100 °C. Dynamic: -20 °C to +100 °C. Reference:84100-10

Goupilles Élastiques Série Épaisse - E (Goup Elast E) Inox A1 - ISO 8752 Modelo:62702

Ball lock pins are used for easy fastening or joining of components. The two balls are disengaged by pressing the push button and the pin can be slipped into holes in the workpieces. When the push button is released, the balls lock the connection securely. Shear force double shear (F) = S · τ aB max. The values given for the shear force are the theoretical breaking load. These are non-binding reference values without consideration of safety factors and exclude any liability. The values given are for information purposes only and do not constitute a legally binding assurance of properties. The load values have been calculated in accordance with DIN 50141. Each user must determine individually whether the ball lock pin is suitable for the respective application. Different materials in which the ball lock pins are used, weather conditions and wear can influence the determined values. Reference:03420-10

The surface of the hexagon head bolt is polished and, with regard to design optimised for the use in hygienic environments. The bolt head is convex on the top face and the collar has a conical formed top surface. Instead of troublesome embossing or indentations, the bolt head is smooth with a surface finish of Ra 0.8 µm. Dirt and residue from products or cleaners seldom adheres and easy cleaning is ensured. Reference:07170-15 Material:Stainless steel 1.4404 Version:Polished

Caches Écrous Hexagonaux Blancs - RAL 9010 Polyethylene

Steel 1.0718 or stainless steel 1.4305. Version: Electro zinc-plated steel. Bright stainless steel. Note: Pin with groove, suitable for DIN 71752 clevis. Secured with a DIN 6799 E-type circlip (alternatively a KL or SL clip). When combined with a suitable clevis and tang, forms a fully functional clevis joint. Reference:27621-01

Cable ties are made by high quality of Nylon 6.6. resin. The property of this material is in moisture absorbed and released. Cable ties require to be contained the moisture and packed in the sealed packaging to have optimal performance. Hence, the conditions for keeping the packaging of cable ties are very important.

Aucune information supplémentaire sur ce produit. EXEMPLE DE COMMANDE:412408-2,9X6,5

Le vérin de bridage pivotant pneumatique convient pour le serrage de pièces par le haut. La fonction de pivotement et de serrage s'effectue via un système pneumatique. La fonction de pivotement garantit une insertion et un retrait faciles de la pièce. Ceci assure un accès optimal à la pièce. L‘embase du corps offre des possibilités de montage diverses, afin que le vérin de bridage pivotant puisse être positionné de manière optimale auprès de la pièce a serrer. Les vérins de bridage pivotants sont disponibles avec pivotement à gauche ou à droite. Les vérins de bridage pivotants pneumatiques peuvent également être positionnés à différents emplacements de la pièce et actionnés suivant un ordre prédéfini. La commande s'effectue manuellement ou à l'aide d'une machine. La force de serrage et la force de retenue sont données pour 0,5 MPa. Référence:04365 Matière:Acier de traitement

The floating joint unit is a bolt for connecting two components, that permits a desired movement of those components in relation to each other. The floating joint unit is mainly used when: a temperature change alters the dimensions of a component assembly inaccuracies occur manufacturing tolerances must be compensated for the position of the components varies due to dynamic loads Reference:07532 Temperature range:-20 °C to +80 °C

Latches with draw bail for securing and locking hatches, container lids, machine cladding etc. By exceeding the dead centre they resist vibration. The locking force is applied by drawing on the bail. The latches can be screwed down or riveted. We recommend using countersunk screws for fastening the components. Order catch plates separately. Reference:05531 Material:Steel or stainless steel 1.4301

Pointe Annelée Tête Plate Inox A2

Milled toothing, straight teeth. Engagement angle 20°, bright. Axis angle = 90°. Note for ordering Bevel gears are supplied singly. To obtain a pair of bevel gears, please order the specified mating gear as well. Reference:22430 Material:Steel 1.0503 (C45)

Black thermoplastic. Steel grade 5.8 or stainless steel 1.4305. Version: Metal parts trivalent blue passivated steel or bright stainless steel. Note: Star grips with projecting steel bush and blind hole or female thread are especially suited for cross pinning. Drawing reference: Form H: bush with blind hole Form K: tapped bush Form L: external thread Reference:06210 Form H:bush with blind hole Form K:tapped bush Form L:external thread

Écrou hexagonal indesserable avec bague metal Inox A2 Bague métal Recommandé en milieu agressif (chaleur, acidité,...). Modelo:62632

Housing 1.4308 stainless steel, from size 5 1.4301. Clamping arm 1.4301 stainless steel. Buffer natural rubber. Screw stainless steel A2. Version Housing and lever arm bright. Screw ISO 4017, grade 70, bright. Note Clamping element with integrated highly elastic, shaperetaining natural rubber buffer. Together with a chain tensioner set, sprocket set or a tension pulley, the clamping element makes a readytoinstall tensioning unit suitable for tensioning chain and belt drives. Suitable for both tensioning directions. The clamping elements are maintenancefree and tearoff resistant. The clamping element is fastened to the machine component through a bore. If necessary, a heavyduty dowel pin can be inserted in the positioning notch “P” for torque support. Reference:22281-14 Temperature range:-55 °C to +85 °C

A4 Stainless Steel Impact Socket

Torx Bit For Stainless Steel Tamper Proof Screws

Ecrou à crans Inox 304 EXEMPLE DE COMMANDE:264114-40 Dimensions disponibles:du DN40 au DN100 mm Normes:CE 1935/2004

Rivets Étanches Tête Plate - A2/AISI 420 (Riv étanche aisi 420) Inox A2 - TYPE ISO 16585

Hexagonal Nuts to Weld (ECR TO WELD) Inox A2 - DIN 929 There is a variant in Inox A4

Poignée traitée et chromée. Tige, butée et embout trempés et chromés. Nota : L'extracteur est utilisé pour démonter les goupilles ou cimblots de positionnement (03105, 03106, 03107,03108, 03325) munis de taraudages M3 à M8. Indication de dessin : 1) Butée 2) Poignée 3) Tige 4) Goupille 5) Vis de serrage 6) Douilles de guidage 7) Vis CHC 8) 1 jeu d'embouts Référence:03328

Housing, stainless steel 1.4301. Bearing, stainless steel 1.4125. Seal, rubber NBR. Note Pillow block bearings consist of a sealed singlerow ball bearing with a spherical outer ring which is mounted in a housing. Because of the spherical outer surface of the bearing, shaft misalignment can be compensated for. The bearings are manufactured with a plus tolerance. This results in transition or press fits when using shafts with htolerances. The shaft is secured by grub screws on the inner ring. In normal applications, pillow block bearings are maintenancefree due to the lifetime lubrication. In difficult environmental conditions relubrication can be carried out over the grease nipple. All housing dimensions are nominal dimensions for which the usual casting tolerances must be taken into consideration. Reference:24240 Version:Bright Temperature range:-15 °C to +100 °C