Termékek olapl (52)

Syntech Pavidamp A three-component formulation, with a fluid epoxy resin base in aqueous emulsion (A + B) to be mixed with the third component (C) consisting of white cement and micro-quartz, specially designed to be used as a primer for cementitious surfaces in the presence of humidity and in conditions of hydraulic counter-thrust. Generally referred to as “wet-bonding”, it is particularly suitable as an anti-humidity barrier for the subsequent laying of parquet. Building connection layers and smoothing cement surfaces; bottom layers for resinous coatings of floorings in the presence of damp subbases; anti-humidity barriers in concrete, brick and stone masonry; surfacings of porosity, cracks and superficial irregularities. As protection from rising damp for bases where operations with polyurea resins SYNTECH POLYUREA will be carried out. The support on which the resin system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilatations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. Apply by roller, brush or spray from 150 to 200 g / m2 of Syntech Primer EP-W to consolidate the substrate and facilitate the adhesion of the subsequent coating. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Prepare the mixture of the 2 liquid components (A+B), pouring the contents of the component B in the container of the component A. Mix with drill for about 2 minutes. Add the pre-dosed hydraulic binder (high resistance white cement) to the mixture A+B, and mix with a mixer drill. To disperse the product optimally, pour the powders (component C) a little at a time, continuing to stir with drill, until a homogeneous lump-free mixture is obtained. If it is used as a base: dilute with 10-15% by weight of clean, soft water and apply with a roller or brush. Indicative consumption: 0.4-0.5 kg/m² on regular supports, 0.7-0.9 kg/m² on irregular supports. If it is used for fine finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 60-70% spheroidal quartz (0.04-0.25 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 1-2 kg/m². If it is used for medium finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 70-80% spheroidal quartz (0.1-0.5 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 3-4 kg/m². From 0.50 to 0.60 kg of SYNTYECH PAVIDAMP for each square metre of surface to be covered. Pail 3.8 kg [A] - Pail 1.2 kg [B] - Pail 5 kg [C] - Kit: 1 Pail 3.8 kg [A] + 1 Pail 1.2 kg [B] + 1 Pail 5 kg [C]

Scale a castello con inclinazione 60 gradi conforme a D.lgs 81/2008 e ISO 14122. Le nostre scale a castello sono realizzate con materiali certificati e di alta qualità. Curate nei dettagli, offrono una sicurezza di salita maggiore rispetto alla concorrenza perchè il gradino è realizzato con uno scatolato estruso di alluminio 200x30mm con una superficie antiscivolo che garantisce un'ottima presa e appoggio del piede anche in caso di maltempo. Gradini antiscivolo in alluminio estruso 200×30 mm con zigrinatura UltraGrip Corrimano da Ø 40 mm per una presa sicura ed ergonomica Passerella in alluminio con zigrinatura antiscivolo Lunghezza passerella a scelta da 400 a 3000 mm Fermapiede a norma di legge facile da installare Altezza parapetto 1100mm Inclinazione 60° per ingombro ridotto Staffe di fissaggio in acciaio INOX Montante laterale in alluminio estruso 88×35 Tappi di chiusura in PA6 avvitati per evitare accumulo di polvere e tagli Telaio munito di ruote posteriori Altezza scala:300 a 4800 mm Inclinazione:60° Larghezza Gradino:600, 800, 1000 mm Lunghezza piattaforma:400 a 3000 mm

HIGH BASE CLIP TAG FOR PLASTIC RODS CODE:CT HIGH BASE Variants:Magnetic acoustic, AM 58 Khz, Radio frequency 8.2 Khz Colors:Crystal/Transparent, Natural/Neutral, Black, Ice, White Measures:48 X 30 Thickness. 20 Neck pieces:500 Neck size:45X31X17

HDC BLACK CERAMIC CLADDING BENEFITS This type of chromium oxide based coating is black in color. The piece coated with "HDC" ceramic offers excellent resistance to mechanical wear and corrosion. Furthermore, excellent finishing results are obtained. USE OF COVERING ON: • Drawing cones • Aluminum pulleys • Rollers • Capstans up to a diameter of 1300 mm • Sealing rings Black Ceramic Cladding

La nostra azienda produce una vasta gamma di guarnizioni, nastri e sigilli di garanzia per capsule, per l'industria delle bevande, alimentare, farmaceutica, cosmetica e chimica. Guarnizioni in Polespan, Guarnizioni biadesive, Polespan e SIGILLI di GARANZIA

find a wide application in cases where it is necessary to feed bulk loaded components into the bowl, automatically or individually, in the position and at the speed desired. The output of the pieces can occur through one or more channels placed side by side or overlapping, with timed or continuous flows. To meet specific production requirements, these can be used for removing any extraneous, defective components as well as those which exceed the thresholds. The scope of application for circular vibrating bases includes the entire field of automation for mass production: from electronics to mechanics, from electronics to hydraulics, from food to pharmaceuticals to manufacturing/packaging. Circular vibrating bases can be employed individually or put into feeding assemblies within the assemblage or automated processing systems. They are, moreover, isolated from the support structure thanks to the presence of special anti-vibration feet. The intensity of the vibration can also be...

Versatili basi barra seno utilizzabili per lo staffaggio e le lavorazioni di particolari meccanici. Facilmente riconfigurabili come squadra 90°

Le basi vibranti lineari di questa serie sono state progettate per manipolare oggetti delicati, ma sono capaci di offrire prestazioni eccezionali sia in termini di lunghezza che di peso. La loro costruzione modulare consente di utilizzarli senza contrappeso fisso o mobile, se necessario, per adattarsi alle esigenze di spazio.

Soluzioni Alimentari, azienda specializzata in prodotti senza glutine, distribuisce a rivenditori, farmacie, ristoratori e pizzerie piatti pronti gluten free. La base per pizza senza glutine è di produzione artigianale, stesa a mano, così da ottenere una pizza croccante.Ogni pezzo è confezionato singolarmente in alluminio.

Programma di ricostruzione strutturale del capello a base di cheratina ed estratto di noce. La cheratina è il componente principale del capello, la fondamentale proteina strutturale, mentre l’estratto di noce ancora verede è ricco di polifenoli e un reitcolo sulle proteine dei capelli, agendo in sinergia con la cheratina naturale. La linea si compone di: Shampoo (fase 1) formulato per detergere delicatamente i capelli deboli; Maschera (fase 2) che ripara la fibra del capello danneggiato e lo rende elastico; Fluido (fase 3) senza risciacquo, che si lega subito al capello per ringiovanirlo e restituirgli la sua vera bellezza; Capsule Vitaminiche (fase 4) a effetto condizionante istantaneo, che agiscono sulla superficie del capello per fissare gli ingredienti nutritivi delle fasi precedenti, per prevenire le doppie punte e proteggere dalle aggressioni esterne. Ricche di vitamine A, B1, B2, B5 (Pantenolo), C, E, F, H e PP (Niacina). Il video: https://www.youtube.

I ponteggi a perni GBM sono la soluzione più adatta per chi necessita di un ponteggio sicuro, dall’utilizzo rapido e semplice: il collegamento tra i telai avviene tramite correnti e diagonali in tubo aventi alle estremità dei fori di diametro idoneo all’inserimento dei perni saldati sui montanti dei telai stessi.

Zeus is a bottle rack display with a swivel triangular base perfect for promoting important labels. Zeus pays attention to the housing of the bottles: positioned inclined and inserted in plexiglass supports. The totem structure can display a total of 18 bottles, 6 per side.

TRAMOGGIA IN LAMIERA FONDO INOX COMPLETA CON MICRO PALETTA KG 60

Esploso con pinza BAS

Frattazzo gommaspugna. Questo articolo è disponibile con base in gommaspugna dura in colore blu/grigio, oppure morbida in colore arancio. Il supporto è in polistirolo antiurto. Il manico è disponibile in: simil-legno, polistirolo antiurto, poliuretano, legno. Il supporto è disponibile in: poliuretano, polistirolo, alluminio. La base è in gommaspugna, disponibile in diversi: colori, porosità, densità.

Presse a bombare e manipolatori automatici Serie DPO-MAP: Presse idrauliche con capacità da 150 a 2000 tonnellate - Diametri dischi da 300 a 12.000 mm. Le unità di bombatura Parmigiani si compongono di una pressa idraulica a portale serie DPO e di un manipolatore automatico serie MAP. I movimenti di pressa e manipolatore, spostamento, sollevamento e rotazione dei dischi, sono sincronizzati. Un solo operatore è in grado di controllare l’intero ciclo di lavoro dal pulpito di comando centralizzato. Con STRADIVARI® Playback System, il più avanzato sistema di controllo attualmente disponibile sul mercato, sviluppato internamente dallo staff R&D Parmigiani, che consente la produzione in automatico di una vasta serie di fondi.

Risolvete i vostri problemi di generazione di energia con il nostro servizio di noleggio di generatori a gasolio containerizzati da 500 kVA sia che stiate affrontando un' interruzione di corrente in emergenza o vi stiate occupando di un progetto pianificato. Per un' energia flessibile e portatile, un generatore containerizzato da 500 kVA farà al caso vostro. I dati sono basati su 50 Hz. Per maggiori informazioni, potete richiedere una scheda dei dati. Il generatore raffigurato potrebbe non essere rappresentativo dell'apparecchiatura disponibile in un determinato momento. I generatori sono racchiusi in container in acciaio ISO da 20' o 40' dal design personalizzato. Design modulare per una flessibilità ottimale per l' ideazione del progetto. È disponibile una gamma di trasformatori e di apparecchiature di supporto ad alta e bassa tensione. Livelli di attenuazione del suono super silenziosi senza scendere a compromessi con le prestazioni. Il design dei container

Il Coloring Oil è un trattamento rivoluzionario in olio senza ammoniaca, studiato per coprire i capelli bianchi senza danneggiarne la struttura. Grazie all'ultilizzo di pigmenti di elevata purezza e di principi attivi dell'olio di argan è possibile ottenere un colore luminoso e duraturo.

Sono stampate con acciaio di qualità per le normali applicazioni o con acciai inossidabili AISI 304, 316 per applicazioni speciali: • Realizzate per durare nel tempo garantiscono robustezza e solidità abbinata ad un’ ottima resistenza all’usura ed alle sollecitazioni meccaniche. • Il profilo parabolico permette di guidare il getto del prodotto verso lo scarico evitando dispersioni che ricadano nel piede dell’elevatore causando diminuzioni di portata. • Le superfici liscie e arrotondate permettono Io scarico rapido e totale della tazza e la sua pulizia immediata. • Sono particolarmente indicate per il lavoro intenso, per trasporti gravosi anche delle grosse granulometrie. • Le tazze vengono prodotte con lamiera di spessore standard come indicato nelle tabelle o con spessori maggiori secondo le Vostre esigenze. • I fori sono bombati per garantire una perfetta tenuta del bullone la cui testa si inserisce completamente nella cinghia.

Gabrieli srl è una realtà bresciana specializzata nella tornitura automatica monomandrino e nelle lavorazioni meccaniche su macchine transfer e centri di lavoro. Lavoriamo esclusivamente secondo il disegno del cliente e la ns. competenza principale risiede nella lavorazione di leghe di ottone. Alcuni esempi di prodotti che realizziamo su specifica del cliente: raccordi nipples, dadi, controdadi, rosette, bocchette, maniglie, ghiere, attacchi portagomma, raccordi ogiva, calotte, manicotti, tappi filettati, raccordi aria, raccordi a saldare, ecc. I nostri clienti sono attivi in un'ampia gamma di settori industriali tra cui: rubinetteria, valvolame, raccorderia, riscaldamento, produzione di tubi flessibili, impianti gpl, idraulica ecc. Gabrieli srl ist auf automatendrehen und auf die Bearbeitung von Warmpressteilen spezialisiert. Einige Produktbeispiele: Schlauchverbinder, Tauchhülsen, Holländer-Verschraubungen, Muttern, Muffen usw.

Basi per ombrelloni di varie misure e colori

Sanaxil I Natural, protective, decorative, breathable, pigmented, non-toxic, anti-mold plaster, with stabilized potassium silicates, for interiors and exteriors. Substantially mineral formulation which, thanks to the natural alkaline pH of potassium silicate, develops a strong antibacterial and anti-mold action. Sanaxil I is a versatile and valid product in various application fields: in green building interventions, in new constructions and in the restoration of period and monumental buildings. The product does not form a film, thus avoiding detachment and flaking phenomena and, while ensuring excellent water repellency, ensures high values of permeability to water vapor thanks to its porous and microcrystalline structure, perfectly compatible with mortars, plasters and all other common elements of the body masonry. Physical-mechanical performance and durability are coupled with a vast choice of colors that cannot be altered over time; characteristics which, combined with the ease and practicality of application, make the product extremely versatile and adaptable to any project requirement. Restoring protective coatings based on stabilised potassium silicates, for vertical and horizontal surfaces. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". Existing paints (washable, organic, solvent-based etc.) must be removed. Homogenise the surfaces by applying the fixative Sanaxil Fix. Spread SANAXIL in two coats: the first, for simple deposition, with steel trowel, the second, for spreading and finishing, with sponge float. The application of the second coat must be carried out, when the first coat starts to dry, under one of two suggested conditions: with dry trowel, for smooth surfaces; with moistened trowel, for antique-effect surfaces. Sanaxil I is dry to the touch after 4 hours, it can be overcoated after 2-5 hours, while it will be dry in-depth after 16-32 hours. Indicative consumption depending on the different particle sizes of Sanaxil I available: 1 mm GRAIN: approximately 1.25 -1.40 kg/m²; 1.2 mm GRAIN: approximately 1.40 -1.55 kg/m²; 2 mm GRAIN: approximately 1.85 -2.15 kg/m²; 2.2 mm GRAIN: approximately 2.00 -2.30 kg/m². The indicated yields refer to smooth supports and are for guidance only. Actual consumption must be identified with a suitable practical test. Pail 5 kg - Pail 25 kg

Sanaxil Fix Reinforcing, fixative, transparent primer, based on stabilised potassium silicate for the preliminary treatment of the surfaces to be painted and/or plastered with silicate-based, lime putty, systems, for ecological building interventions, new buildings and for the restoration of vintage buildings and monuments. Sanaxil Fix is a product consisting of potassium silicates. It is highly breathable and is not subject to thermoplastic effects. It does not contain resins, solvents, thinners and harmful or toxic emanations. Free of V.O.C. "Priming" fixative treatment of coatings, paints or putty coat based on lime putty, potassium silicate and siloxanes in general. Dust-proofing, reinforcing, cortical treatment for surfaces of pulverising plaster. Organic type paints (washable, solvent-based etc.) where present, must be thoroughly removed. The support should, in any case, be, clean, homogeneous, compact, dust-free. SANAXIL-FIX can be applied to substrates in masonry, on cement surfaces, lime-based surfaces, on well anchored mineral paints. They can be applied by brush, roller or spray: the number of coats required and the most appropriate dilution ratio with water will be determined as a function of the absorption conditions and degradation of the support. The admissible dilution range provides for additions of water up to a maximum ratio of 1:1. Apply from 0.10 to 0.15 litres of Sanaxil Fix per square metre of surface to be treated. Plastic can 5 l - Plastic can 20 l

Sanalink Hydraulic lime and natural light aggregate based fibre-reinforced mortar. It has high water vapor permeability characteristics, low bulk density (reduced thermal conductivity) and limited water permeability. Ideal for the construction of internal and external walls and masonry for new buildings, the renovation of existing buildings, green construction and the restoration of antique and monumental buildings. Sanalink has exceptionally strong water vapour permeability and adhesive properties and a particularly low elastic modulus. Its reduced bulk density makes it particularly advantageous in determining the thermal values ​​of the masonry, thanks to the thermal conductivity values, inferior to conventional cement mortars or lime based. It has physical, chemical and aesthetic properties very similar to antique mortars and is composed of raw materials of natural origin. The combined use of natural binders, micro-fibres and light inert pozzolanic materials guarantees high quality performance in terms of ductility, chemical resistance and water vapour permeability. It can be used for brickwork, tuff, stone and mixed masonry walls and is therefore recommended for the restoration of antique masonry, green construction and, in general, quality interior and exterior constructions. Mortar used for the construction and rehabilitation of interior and exterior masonry in solid or perforated concrete blocks, perforated bricks, solid bricks, tuff, natural stone and stone blocks in general. Application surfaces must be clean, free of dust, contamination, crumbling, inconsistencies, etc., and adequately saturated-surface-dry with water. Add approximately out 2/3 of the mixing water to the mixer and gradually add Sanalink and the rest of the water until a homogeneous, lump-free mixture of the desired consistency is obtained. The required mixing water is approximately 12-16% by weight (approximately 3.5 litres per 25 kg bag). Application can be manual (trowel) or mechanized (pumps, extruders, etc.). Approximately 17 kg/m² of Sanalink for every centimetre of thickness to be implemented (approximately 1700 kg per cubic metre). Bag 25 kg

Syntech Profix A two-component paste with a polyester resin base for the rapid realisation of structural fasteners and anchors for inserts and connectors in general. This quick-setting resin (which hardens in just 6 minutes at 20° C) facilitates the use of metal inserts a mere 2.5 hours from installation. Syntech Profix is a system that is easy and quick to use that provides high performance in terms of penetration, adherence and mechanical resistance. In particular, in concrete, natural stone, full and hollow brick works etc., the resin Syntech Profix, permeates the porous systems that delimit the perforation, allows the achievement of very high admissible loads, adjustable and scalable through variations of the fastening element, the anchor depth and so on. Syntech Profix is packaged in a two-compartment cartridge, whose special tip mixes the two components directly during extrusion, activating the polymerisation reaction instantly. Fixing of connectors, bars, plates, metallic structures, fencing, shutters, gates, shelves, reinforcing rods etc., in different types of media, with particular effectiveness in the presence of concrete, natural stone, bricks, drilled (through the perfo sleeves) etc. The application surfaces should be clean, free of incrustations, crumbling and non-adhering parts, dust etc. The following accessories are provided for easy use of the cartridges Syntech Profix: - Gun for resins in a cartridge with rack-and-pinion piston. - Perfo sleeves (only for hollow masonry and perforated blocks) - Spout mixer for two-compartment cartridges (mixing tip) Extrude Syntech Profix in the required quantity in the fastening seat. Attach the metal insert to be anchored within a few seconds after the extrusion. Do not touch the insert for any reason until the ascertained hardening of the resin. Approximately 1.72 kg of Syntech Profix for each cubic decimetre of volume to be filled (variable according to the conditions of use). Bi-mix cartridge 400 cc - Box: 12 x (Bi-mix cartridge 400 cc).

Sanaxil P Breathable, natural, non-toxic paint, for external and internal surfaces, for adhesion and microcrystalline structure, based on stabilized potassium silicate. Mineral-based, active formulation, with high natural mildewcide and anti-condensation properties, prepared according to the traditional recipes, for use in ecological building interventions, new buildings and in the restoration of vintage buildings and monuments. Sanaxil P consists of potassium silicate and natural pigments. It has very high breathability, remarkable mildewcide and antibacterial properties. It has no solvents, thinners, harmful substances and toxic emissions in general, and does not have thermoplastic effects. Restoring and decorative paints for internal and external environments. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". Pre-existing paints (washable, organic, solvent based etc. ) must be thoroughly removed. Preliminarily treat the support with the fixative Sanaxil Fix. Apply Sanaxil P, using a brush, roller or spray, in the number of coats required by the absorption condition of the support. Sanaxil P is "dust-free" (it has started to be consistent to the touch) after about 1 hour. It can be overcoated after 4-6 hours, while it will be dry in-depth after 10-16 hours. Sanaxil P can be used as such or diluted with Sanaxil Fix, at a rate of 15-20% by weight. Apply from 0.30 to 0.40 liters of Sanaxil P per square metre of surface to be painted. Pail 4 l - Pail 14 l

Sanaxil I - Therm Smoothed mineral coating for interiors and exteriors with potassium silicates with chemical adhesion, anti-condensation, insulation, mould resistant, thanks to the addition of hollow glass spheres. Sanaxil I - Therm due to its mineral nature with chemical adhesion, revolutionizes the concept of adhesion to the support, penetrating deeply into the pores of the wall to then react with its components and form a unique and indissoluble "silicating" whole. With a final appearance similar to civil plaster. The product does not form a film thus avoiding detachment and peeling phenomena, it ensures a permeability to water vapour thanks to its microcrystalline structure of the same porosity as the wall while guaranteeing excellent water repellency. Elasticity and hardness are coupled in maximum degree with a wide choice of colours not alterable over time; characteristics that, combined with the ease and practicality of application, make the product extremely multi-functional, adaptable to any project requirement. Restoring protective coatings based on stabilised potassium silicates, for vertical and horizontal surfaces. All products in the Sanaxil I – THERM series cannot be attacked by mould. Recommended as a finish in "cladding" insulation systems, as it helps to increase the thermo-acoustic and anti-condensation coefficient. Stone, masonry, concrete and any type of plaster. The Sanaxil I - Therm system can be applied directly on surfaces treated with mineral paints or new surfaces. If there are residues of organic paint on the support (washable, solvent-based paints, etc.), before application it is necessary to remove them by stripping or sandblasting, and also never apply on plaster, under the beating sun, on warm or wet walls. During application, cover areas that are not to be painted such as jambs, doors, windows and floors because silicates attack glass, metals, ceramics, glazes, paint, marble and granite. Adverse climatic conditions can impose the realization of adequate protection during the application and drying phase of the coating. Never mix with other non-mineral based paints. NEW SUPPORTS Apply a coat of Protech Fix AC - Therm fixative diluted from 20 to 50% with water depending on the absorption of the support. OLD SUPPORTS On old supports, remove the old paint by brushing, fill in any holes or imperfections in the wall with a suitable filler, proceed with fixing with Protech Fix AC - Therm impregnating agent diluted 20 to 50% depending on the absorption of the support. The product is ready to use if necessary add a little water and stir slowly. Apply a coating layer with a stainless steel trowel with a thickness equal to that of the granules it contains. Pass again with a cutting spatula to remove any excess material. After light drying, pass over with a plastic trowel with rotary movements to compact, even out and achieve the full plaster effect. On large surfaces, it is recommended to apply the product of the same lot and proceed always wet on wet to avoid signs of resumption. Indicative consumption depending on the different particle sizes of Sanaxil I - Therm available: 1 mm GRAIN: approximately 1.6 -1.8 kg/m²; 1.2 mm GRAIN: approximately 1.8 -2.0 kg/m²; 2 mm GRAIN: approximately 2.4 -2.8 kg/m²; 2.2 mm GRAIN: approximately 2.6 -3.0 kg/m². The indicated yields refer to smooth supports and are for guidance only. Actual consumption must be identified with a suitable practical test. Pail 22 kg

Sanaxil Filler Anti-crackling base, based on siliceous aggregates of different particle sizes, potassium silicate, nylon microfibre and specific agents, in a special mix ensuring watertightness, water-repellence, permeability to steam. Available in two different particle sizes, on request. Specific for the reclamation of internal and external vertical surfaces, characterised by significant presence of cracklings from shrinkage (also of width up to 1 mm), for homogenising regularisation in general. It can also be used as a base to obtain a rustic effect of the finish. Particularly suitable for the anti-cracking reclamation of historic buildings. Due to its mineral nature and the chemical adhesion it provides, Sanaxil Filler represents a significant revolution in the traditional concepts of adhesion to supports: it penetrates deeply into the pores, it reacts with the components of the masonry structure creating a homogeneous, indissoluble and breathable "silicated" whole; it does not form films, it is water repellent and resistant to moulds and micro-organisms. When it is applied in combination with paints or putty coats, it substantially improves their durability, because it gives a greater thickness to coatings and paints. Sanaxil Filler is composed of stabilised potassium silicate, silica aggregates and natural pigments. It has high breathability, excellent mildewcide and antibacterial properties. It has no solvents, thinners, harmful substances in general. Subbase micro-smoothing, for subsequent coatings with paint or with putty coat, specific for the anti-crackling reclamation of large vertical surfaces of buildings and condominiums in general. It creates of a thick base to improve the durability of the coating. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". It is recommended that you preliminarily treat the media with the specific fixative Sanaxil Fix (as such, or diluted with water up to a ratio 1:1). Sanaxil Filler should only be used for reclamation and under the conditions described above. It can be applied with a roller or brush, possibly after dilution with 10-15% Sanaxil Fix. Apply from 0.30 to 0.50 kg of Sanaxil Filler per square metre of surface to be treated. Pail 25 kg - Pail 5 kg

Sanafarbe P Breathable, natural, non-toxic paint, for internal and external surfaces, diffusive type, based on lime putty. Mineral-based, active formulation, high natural anti-mildew and anti-condensation capacity, prepared according to the traditional recipes, for use in ecological building interventions and in the restoration of vintage buildings and monuments. Product based on lime putty and natural pigments. Sanafarbe P has a high breathability, remarkable mildewcide and antibacterial properties. It has no solvents, thinners, harmful substances in general. Decorative and internal and external restoration paint. The application supports will be free from fouling, powder, non-adhering parts, etc.; existing paints (washable, organic, solvent based etc.) must be removed. A preliminary fixative treatment of the surfaces is always advisable with a consolidating, transparent, Sanaxil Fix primer, based on potassium silicate. The application of Sanaxil Fix can be done by brush, roller or spray: the number of hands required and the dilution ratio with the most suitable water must be determined according to the conditions and absorption degradation of the supports. The admissible dilution range provides for water addition up to a maximum of 1:1 ratio. Apply by brush, roller, spray, in two coats, spaced-apart, one from the other, by about 24 hours. It allows the easy reproduction of traditional finish type: sponging, rubbing, marbling, infilling. Sanafarbe P is dry to the touch after 2 hours, it can be overcoated after 4 hours, while it will be dry in-depth after 8-16 hours. Apply from 0.20 to 0.40 liters of Sanafarbe P per square metre of surface to be painted. Pail 4 l - Pail 14 l

Protech Sil I Water-repellent, breathable, pigmented, ready-to-use plaster based on siloxane resins dispersed in water. Ideal for the protective coating resistant to water and bad weather in the renovation interventions, both of external facades and of internal environments, of civil and industrial buildings, and in new constructions. Protech Sil I is available in 5 different sizes for the most varied applications: - Very fine (grain ≤ 0.4 mm) - Fine (grain ≤ 0.7 mm) - Medium (grain ≤ 1.0 mm) - Large (grain ≤ 1.5 mm) - Very large (grain ≤ 2.0 mm). "Waterproofing", water repellent, breathable, protective and decorative finish, for masonry surfaces in vintage buildings, subject to protection as "cultural heritage" or otherwise, in restoration, for new buildings, in dehumidifying systems etc. The surfaces of application will be adequately prepared: dry, free from fouling, powder, crumbling parts, incoherent, pre-existing synthetic paints etc. Any lime and/or cement-based plaster, lime painting, compact and anchored, they can be preserved. It is essential to pre-treat with the siloxane fixative Protech Sil Fix. Protech Sil I is ready to use, in the form of thixotropic paste which, after thorough mixing, can be applied immediately. Two layers of application are recommended, each with a thickness not exceeding the size of the calcareous grain contained in the product. After applying the second coat, when the product starts the drying stage, proceed to floating with sponge tool. Indicative consumption depending on the different particle sizes of Protech Sil I available: 1 mm GRAIN: approximately 1.25 -1.40 kg/m²; 1.2 mm GRAIN: approximately 1.40 -1.55 kg/m²; 2 mm GRAIN: approximately 1.85 -2.15 kg/m²; 2.2 mm GRAIN: approximately 2.00 -2.30 kg/m². The indicated yields refer to smooth supports and are for guidance only. Actual consumption must be identified with a suitable practical test. Pail 5 kg - Pail 25 kg