Termékek szűrés (82)

Submerged turbine operating at low speeds combined with an air blower for oxygen input. The Sofie® Submersible Aerator/Agitator is a mixing unit for extremely challenging applications. The units minimise blocking or clogging, the Sofie® can be used as an aerator or an agitator for wastewater treatment. Sofie® is designed to be installed at the base of tanks and to operate either in aeration or in a mixing mode. Sofie® is a good alternative to mechanical fine bubble aerators and is suitable for ponds with oxygen or mixing requirements.

Radial Aspiration and Mixing floatable material with downdraft flow and dual action impeller. The homogenization phase allows re-entrainment with the biological process. FRED units prevent settlement and crust formation as well as mixing the entire basin. Nothing is discharged from the basin. Applicable for Viscous + sludge bulking applications and grease trap systems upstream of biological reactor SBR. 1.1 – 22KW Motors 4 – 6 Pole Speed, Direct Drive 2 + 3 Float Options AISI 304/316 or special SS Special dual action impeller Excellent mixing performance Reliable + non-clogging design Easy installation + removal

Thickening of sewer station sludge Thickening of sludge from urban or industrial effluent treatment plants The sludge suspension is introduced into the centre of the circular thickener. The thickened sludge is discharged at the centre through the bottom. The sludge suspension is introduced into the centre of the circular thickener. This thickening solution is economical and requires little maintenance. Thickeners are usually made of concrete and can also be made of vitrified steel.

Designed for aeration of Activated Sludge Basins in Municipal and Industrial Wastewater Treatment plants. The AQUATUBE® specific design prevents sedimentation and Optimises Mixing and Oxygen Transfer. The AQUATUBE® 90 is designed to be installed on DN100 stainless steel pipe or DN110 PVC using simple fastening system. The AQUATUBE® 70 can be installed on square stainess-steel manifolds or on polypropylene manifolds. DIFFUSER BODY The manufacture of this component in glassfibre reinforced polypropylene gives it excellent resistance to abrasion, high chemical resistance, and substantial mechanical strength. EPDM MEMBRANE The Membrane prevents water from penetrating into the feeders when air is stopped. EPDM MEMBRANE The Membrane prevents water from penetrating into the feeders when air is stopped. POLYPROPYLENE FIXING BRACKETS Allows simple and easy installation on circular manifold (only for Aqua tube® 90)

Slow speed aerators used for aeration and mixing of urban and industrial wastewater in various processes Provided in either fixed bridge or floating designs Ideal for Aerating most types of wastewater or industrial euents The TLF® Turbine Aerator is one of the most ecient aeration products in the marketplace Produces High Mixing and Homogenous Solutions in large lagoons and ASP tanks. IP55 geared motor with IE3 highly efficient rating Coupling sleeve and based materials coated with high grade Epoxy Paint Float can me supplied in various materials including HDPE Rotor made of glass fibre reinforced polyester. The GRP has a low density which allows installation without having to empty the tank and the design also reduces the axial loads on the gearbox.

To assist bio-digestion FB aspirates and breaks high volumes of foam forming on the surface of some biological and thermophilic reactors. Foam is drawn into the volute where the degassing tube allows air to vent to atmosphere and liquid to re-entrain. Nothing is discharged from the basin. Applicable in high foam treating biological reactors, high foaming influent, thermophilic reactors, biological treatment of animal waste.

Totally independent Aerator and Mixer. Air Provided by Blower with Variable Frequency Drive which can regulate oxygen supply from zero to maximum capacity; whilst retaining full mixing and oxygen dispersion capability therefore the units are ideal for SBR ASP & MBR applications.

Fine bubble aeration system for lagoons & large surface area ponds. HDPE Floating Feed pipe sized to provide the required air flow Air supply pipe to difusers Aquatube 70 type Tubular Diffusers Stainless Steel Diffuser Feed Section Concrete ballast to stabilise the diffuser assembly Cost-effective solution Low maintenance Specific modular system Adaptable to any lagoon or large pond Low maintenance requirements Very reliable system easy to install and operate Very competitive design and scope of supply Significant mixing of the total volume within the lagoon The active biomass is aerated effectively and efficiently.

Bladed Horizontal surface aerator suitable for circular, racetrack or rectangular channel. Designed to be maximise oxygen and flow. Use of high-quality materials of construction together with mechanical gear driven equipment. Reliable equipment with extremely long service life. COMPONENTS Brush bridge shaft with anti-corrosion paint Galvanised Steel brush blades or stainless steel Side protection discs Bearings Vertical geared motor with high energy class IE3 enclosure and eciencies Horizontal geared motor with energy class IE3 enclosure and eciencies Geared motor support bracket Upstream and/or downstream rotor cover Automatic grease cartridge Operator safety features on and upstream of the brush aerator

Sludge settling Equipment designed for primary and secondary settling tanks in urban or industrial wastewater treatment plants that contain solids and can then be extracted for sludge processing. Scraper bridge made entirely of aluminium and stainless steel for extremely long durability (compared to galvanised steel solutions in particular). Robust and reliable solution. The Scraper bridge is designed to be installed in circular settling tanks. Hundreds of scraper bridges installed over the last 60 years.

The EUROMIX® vertical shaft floating agitator is designed for all mixing applications and operates at 1000 rpm. The liquid rises to the surface of the tank and discharged at the base. The EUROMIX® flow-guide pipe allows the fluid to be directed to the base of the tank and can be used for deep tanks. The specific flow created ensures the mixing of the liquid. The general basis of the mixing being vertical, the water is directed at very high-speed causing a laminar flow by the agitation unit at the tank base. The EUROMIX® thus prevent the formation of dead zones in the tanks. It prevents sedimentation and rapid settling in holding and mixing tanks.

The FRMD is used to remove the upper layer of foam, oil or fats. The natural flow within the basin, together with the suction of the pump, attracts the surface of the water towards the center of the FRMD. An adaptable floating weir allows the upper layer to enter the pump and be removed from the basin. The weir and the submersible pump are mounted on a robust floating structure held in place by cables and springs or guiding tubes. Depending on the application and the geometry of the basin, the FRMD can be mounted together with a MIX SL (directional submersible mixer) or MIX-AS (floating downdraft mixer) to help the flow towards the weir. Applicable for removal of oil, fats, bulking + aging sludge, recycling of scum in sludge stabilisation + biogas, SBR and ASP tanks.

Polypropylene feeder for grids in bioreactors and degreasing tanks Suitable for both municipal and industrial wastewater treatment plants. Allows the installation of Aquadisc® 250 / 305 / 320 and Aquatube® 70 diffusers. Diffusers are known for their excellent temperature resistance, recyclability, and longevity. Glass Fibre reinforced polypropylene feeder. Noemi® module body, highly resistant to chemical and abrasive attack - standard length tubes of 2 m, which can be designed to fit many tanks configurations Polypropylene support and fixing brackets mounted on stainless steel anchor rods - the profiled shape of the bracket allows the module body to be locked in rotation and ensures its stability in the tank All stainless-steel fixi Drain plug

Multi-purpose, multi-directional, submerged mixer ideal for general mixing and flow generation; adaptable to many tank configurations. Open, dual helical impeller providing intensive; directional sub-surface mixing pattern with minimal surface disturbance and low power to volume performance 1.5 – 22KW Drive Motors 4 + 6-Pole Speeds, Direct Drive AISI 304/316 or other SS Submersible motor – ip 68 protection High quality, low maintenance motor Robust + compact design – minimal vibration Easy installation + removal Directional mixing + flow generation plus general mixing of lagoons Basins + tanks activated sludge processes vey large surface area reservoirs Denitrification + sbr + asp

The removable aeration ramp is a solution to bring oxygen to effluent by fine air bubbles whatever the depth of the basin. These ramps are ideal to overcome an emergency oxygen deficit following a breakdown or an increase in the volume of effluent to be treated.

This product is designed to descale fine bubble membrane diffusers by injecting formic acid to their internal surface. This operation is required when an increase in head loss is observed and to significantly reduce calcium carbonate deposits (carbonation) in the membrane. PUSHCART manufactured in Stainless Steel and complete with the following Storage box in HDPE PVDF lined dosing pump Flexible delivery hose 25m in pvc (reinforced with polyester fibres) Spray nozzle in stainless steel

Designed to be installed in many circular clarifier tanks with flat or slightly sloping bases. Generally used for the treatment of urban or industrial wastewater containing solids that settle quickly and where it is important to be able to remove the sludge as it forms. Aluminium support beams Stainless steel feed well: at the bottom, which dissipates the effluent inlet and at the top, and assists in the sludge being raked towards the sludge discharge cone Sludge cone: collects the sludge transferring from the base of the tank through the suction tubes Suction tubes equipped with extended control valves Stainless steel weir plate and arm for the transfer to the overflow of clarified water

Diffusers designed for aeration of activated sludge basins and tanks in Municipal and Industrial wastewater treatment plants. Quick and easy to assemble by Rotating Diffusers clockwise into Screwed connection. Designed to give optimum performance. DIFFUSER BODY The manufacture of this component in Glass Reinforced Polypropylene gives it excellent resistance to abrasion, most chemicals with significant mechanical strength. EPDM MEMBRANE The EPDM Membrane prevents the penetration of water into the distribution pipework when the air is stopped. CLAMPING TYPE AQUADISC® 250-305: Clamps are manufactured in stainless steel or polypropylene and secures the membrane to the diuser body; AQUADISC® 320: Clamp made of glass fibre reinforced polypropylene. THREAD 3/4’’ CONICAL GAS TYPE FITTING Allows Aquadisc® difusers are mounted by simple turning clockwise

Discharges the volume of clean water without disturbing the sludge blanket or floatable materials on the surface. Ideal for the SBR Process, Sludge Settling Tanks, Sludge Thickeners plus the general decanting process. Comprises of a Stainless-Steel float Circular Type – 10 to 150 m3/h Capacity Rectangular Type – 150 to 3,000 m3/h Capacity Custom manufactured AISI 304/316 or special Materials Can also be equipped with a pump which allows to transfer the water from the sbr to a basin located at a higher level Minimal sludge blanket disruption Adjustable flow rate Avoids discharge of floatable materials Straightforward design + installation

Leader in the field of industrial filters Als führendes Unternehmen im Bereich industrielle Filterung hat sich NEGOFILTRES als erstes Unternehmen Frankreichs voll und ganz auf die Herstellung, den Vertrieb, die Zulieferung und den Import sämtlicher Filtertypen für Industrie, Bauwesen und Design spezialisiert. - Filter, Filtereinsätze und Metallfiltergehäuse - Maßgeschneiderte Filtration für die Industrie - Siebe, Gitter und Filtermedien aus Edelstahl - Papier- und Synthetikfilter - Bau kompletter Filteranlagen - Import und Vertrieb von Filtermedien (großer Lagerbestand) - Lochbleche, geschweißte Gitter und Streckmetall - Verschiedene Teile nach Maß (Kunststoff, Metall...) Dank über 20-jähriger Erfahrung in internationalen Industriestrukturen, konnte Firmengründer Christophe DAVEAU hervorragende Beziehungen zu französischen Partnern und Zulieferern aus dem Ausland aufbauen.

Tous ces filtres sont réalisés sur mesure, du prototype à la grande série. – Toile métallique inox, acier, laiton de 3µm à 10 mm – Tôle perforée inox, alu, acier, laiton de 0.5 mm à 25 mm – Métal déployé inox, acier, laiton de 80µm à 20 mm – Fil métallique inox, alu, Laiton, acier de dia. 25µm à 10 mm Assemblage par plissage, pliage, découpe laser, soudure, collage, roulage & emboutissage, selon le savoir-faire de nos partenaires. – Cartouche plissée – Filtre métallique – Grille sertie et emboutie – Panier filtrant – Conception de filtre sur mesure

NEGOFILTRES est le spécialiste du filtre industriel. Notre entreprise de filtration industrielle. Leader de la filtration industrielle NEGOFILTRES est la première société en France à se spécialiser entièrement dans la filtration industrielle : fabrication, négoce, sous-traitance et importation de tous types de filtres pour l’industrie, l'architecture et le design. – Filtres, cartouches et crépines métalliques – Filtration industrielle sur mesure – Tamis, grilles et médias filtrants inox – Filtre papier et synthétique – Création d’ensembles complets de filtration – Importation et négoce de médiats filtrants (stock important) – Tôle perforée, treillis soudé et Métal déployé – Pièces diverses sur mesure (plastiques, métalliques…)

FILTRATION - APPARATE UND ZUBEHÖR Leader in the field of industrial filters Als führendes Unternehmen im Bereich industrielle Filterung hat sich NEGOFILTRES als erstes Unternehmen Frankreichs voll und ganz auf die Herstellung, den Vertrieb, die Zulieferung und den Import sämtlicher Filtertypen für Industrie, Bauwesen und Design spezialisiert. - Filter, Filtereinsätze und Metallfiltergehäuse - Maßgeschneiderte Filtration für die Industrie - Siebe, Gitter und Filtermedien aus Edelstahl - Papier- und Synthetikfilter - Bau kompletter Filteranlagen - Import und Vertrieb von Filtermedien (großer Lagerbestand) - Lochbleche, geschweißte Gitter und Streckmetall - Verschiedene Teile nach Maß (Kunststoff, Metall...) Schnelle Antwort innerhalb von 48 Stunden - 350 m² großes Produktionswerk in der Nähe von Fontainebleau – Lieferung innerhalb von ganz Europa

La biofiltration est un processus naturel d’oxydation des composés volatils, pour la plupart de nature organique, conduisant à la formation de CO2 et de H2O. Cette transformation est assurée par des microorganismes qui possèdent des propriétés relevant du domaine du “vivant”. Le traitement de l’air par biofiltration permet de traiter les pollutions contenues dans l’air à l’aide d’un biofiltre. Un biofiltre est un filtre biologique. Ces dernières années, de nombreuses études ont été menées sur la filtration de l’air avec pour objectif de trouver des moyens plus efficaces, plus respectueux de l’environnement et toujours moins coûteux. Le matériau filtrant dit « biomasse », est composé d’une matière organique (écorce, tourbe, fibres de coco, etc). La biomasse enveloppée d’une couche d’eau va filtrer les polluants grâce aux micro-organismes et à la couche d’eau présente. Les micro-organismes vont se développer d’eux mêmes grâce à l’eau et aux restes de polluants.

Ensemble complet de filtration pour réseaux urbains ou centrales de traitements. Filtre inox de 1 µm à 1 mm et cartouche polypropylène de 0.1µm à 800µm – Filtre poreux de 0.5µm – Filtre à poche + Corps de filtres tout inox – Filtre multi cartouches

Groupe avec ventilateur, filtratoin absolue pour le confinement dynamique de zone anti-contamination.

CARACTÉRISTIQUES TECHNIQUES – ARMOIRE Construction en tôle d’acier électrogalvanisé avec une épaisseur de 10/10 mm, pliée à froid Finition extérieure en résine époxy antiacides 90 microns et passage dans une galerie thermique à 200°C Coloris gris RAL 7035 Portes vitrées battantes (verre Sécurit 6mm) – double paroi Construction monobloc avec vérins pour mise à niveau Fermeture à clé Ouverture des portes avec un angle de 110° permettant l’extraction des étagères sans les incliner,Pictogrammes normalisés conformes aux normes ISO 3864 Armoire certifiée conforme à la norme EN 16121 Armoire conforme aux articles R. 513266 et R. 513268 du Code du Travail Dimensions extérieures L 600 x P 600 x H 1950 mm Dimensions intérieures L 595 x P 567 x H (2x 930) mm Capacité de stockage* 210L Poids 115 KG

Groupe avec ventilateur et filtratoin absolue pour le confinement dynamique de zone anti-contamination.

CARACTÉRISTIQUES TECHNIQUES – ARMOIRE Construction en tôle d’acier électrogalvanisé avec une épaisseur de 10/10 mm, pliée à froid Finition extérieure en résine époxy antiacides 90 microns et passage dans une galerie thermique à 200°C Coloris gris RAL 7035 Porte vitrée battante (verre Sécurit 6mm) – double paroi Construction monobloc avec vérins pour mise à niveau Fermeture à clé Ouverture des portes avec un angle de 110° permettant l’extraction des étagères sans les incliner, Pictogrammes normalisés conformes aux normes ISO 3864 Armoire certifiée conforme à la norme EN 16121 Armoire conforme aux articles R. 513266 et R. 513268 du Code du Travail

CARACTÉRISTIQUES TECHNIQUES – ARMOIRE Construction en tôle d’acier électrogalvanisé avec une épaisseur de 10/10 mm, pliée à froid Finition extérieure en résine époxy antiacides 90 microns et passage dans une galerie thermique à 200°C Coloris gris RAL 7035 Portes vitrées battantes (verre Sécurit 6mm) – double paroi Construction monobloc avec vérins pour mise à niveau Fermeture à clé Ouverture des portes avec un angle de 110° permettant l’extraction des étagères sans les incliner,Pictogrammes normalisés conformes aux normes ISO 3864 Armoire certifiée conforme à la norme EN 16121 Armoire conforme aux articles R. 513266 et R. 513268 du Code du Travail Dimensions extérieures L 1140 x P 600 x H 1950 mm Dimensions intérieures L (2x 503) x P 567 x H 1864 mm Capacité de stockage* 350L Poids 180 KG CARACTÉRISTIQUES TECHNIQUES – CAISSON FILTRANT Construction en acier électro galvanisé 10/10mm, recouvert de peinture époxy bleue Ventilateur axial (turbine)